Kayak Monster Dolly

  • Status: Pending
  • Hadiah: $300
  • Penyertaan diterima: 18

Keterangan Peraduan

This unit is a kayak dolly that allows a kayak to be rolled around. It will attach to the top of the kayak. The frame must be able to rotate within the connection points as this will allow the wheels to be raised and lower by an actuator. below are specifications
Made out of ½ inch steel tubing – Unit will be one piece with one one piece bent to accommodate each angle.
Connectors points: 2 – 3 inch pieces that clamp around the steel tubing to hold it in place. It will have one bolt hole in each corner. It shouldn’t be more the 2 inches wide and 3 inches long and ¼ inch thick. Is should be able to handle 300 lbs of force.
Frame should be 34 inches wide to the middle of the 90 degree bends on each side and 20 inches from the middle of the bend downward
8 inch Plunge casters will be mounted in the end of the downward legs of the unit. These will be held in place with a bolt that runs through the frame and plunge caster insert.
A 1 inch by 2 inch steel tab would a welded on the steel tubing at 90 degrees with the tubing laying flat on the ground. A ¼ inch hole should be drilled in the middle of the hole.

UPDATE: A 16 inch actuator will connect into the tab on the frame and will go to the rear of the frame and will connect to a 14 inch cross member. I need the design in solid works.
The length of the actuator is 16 inches. it goes between the frame and the stabilizing cross rail. When activated it will push the frame moving the wheels up and down.
Thanks for your interest

Kemahiran-kemahiran Cadangan

Penyertaan teratas dari peraduan ini

Lihat Penyertaan Lain

Papan Penerangan Awam

  • pankj12345
    pankj12345
    • 5 jam yang lalu

    #extended

    • 5 jam yang lalu
  • Yohanesujang
    Yohanesujang
    • 11 jam yang lalu

    Please check feedback #17 thx

    • 11 jam yang lalu
  • paislarx12
    Pemegang Peraduan
    • 1 hari yang lalu

    Yes the kayak has a seat and the dolly will bolt on behind it and will be left on the kayak and not be removed.

    • 1 hari yang lalu
    1. milivoja
      milivoja
      • 1 hari yang lalu

      Ok, thank you for your information.

      • 1 hari yang lalu
  • milivoja
    milivoja
    • 1 hari yang lalu

    Do your kayak have a seat? and do you plan bolting dolly to your kayak before transport.

    • 1 hari yang lalu
  • paislarx12
    Pemegang Peraduan
    • 2 hari yang lalu

    I need the drawings in solid works. Thanks.

    • 2 hari yang lalu
  • paislarx12
    Pemegang Peraduan
    • 2 hari yang lalu

    You can pick the wheels as long as they are 8 inch pnematic

    • 2 hari yang lalu
  • cgblenderer
    cgblenderer
    • 2 hari yang lalu

    Can the format of the file be Not in Solidworks? Or, are you willing to accept exchange formats?

    • 2 hari yang lalu
  • arthuralbert
    arthuralbert
    • 2 hari yang lalu

    Hello, Do you have the models for wheels and Actuator or we can pick by ourselves?

    • 2 hari yang lalu
  • milivoja
    milivoja
    • 3 hari yang lalu

    Hi, i will deliver you in few days fully modeled with 3D presentation. Thank you.

    • 3 hari yang lalu
    1. milivoja
      milivoja
      • 3 hari yang lalu

      I hope you will not pick the winner yet

      • 3 hari yang lalu
  • Symaths
    Symaths
    • 3 hari yang lalu

    Brother apologize I'm interested in your project, I wanted to ask you for what purpose the structure itself is built, and where the kayak will be placed. Do you need 2D CAD drawings with the indicated measurements or a 3D photorealism of how the structure will look?

    • 3 hari yang lalu
  • Babs3D
    Babs3D
    • 3 hari yang lalu

    Some of the details are vague. Can you make a side view sketch as well. Maybe a picture of something similar on the market may help too.

    • 3 hari yang lalu
  • paislarx12
    Pemegang Peraduan
    • 3 hari yang lalu

    I have added another drawing and updated the description a bit.

    • 3 hari yang lalu
  • testevpsa
    testevpsa
    • 3 hari yang lalu

    Hello Sir, Please, could you detail better the project? Maybe a more explanatory drawing? What is the actuator dimensions?

    • 3 hari yang lalu
  • stevenind
    stevenind
    • 3 hari yang lalu

    im join the result will be send as soon as possible.

    Best Regards
    Steven

    • 3 hari yang lalu
  • paislarx12
    Pemegang Peraduan
    • 4 hari yang lalu

    The actuator should be horizontal to the frame not vertical. Plunge caster slide into the bottom of the frame. Not bolted from the side. The frame would need radius corners for safety purposes.

    • 4 hari yang lalu
    1. cgblenderer
      cgblenderer
      • 4 hari yang lalu

      Sir, you should comment on my entry itself.

      • 4 hari yang lalu
    2. cgblenderer
      cgblenderer
      • 4 hari yang lalu

      Is the model going to be used for 3D printing?

      • 4 hari yang lalu
  • diegome1992
    diegome1992
    • 4 hari yang lalu

    Hello you could attach another image to understand better the general shape

    • 4 hari yang lalu
    1. paislarx12
      Pemegang Peraduan
      • 4 hari yang lalu

      I will first thing in the morning.

      • 4 hari yang lalu
  • WProductDesigner
    WProductDesigner
    • 5 hari yang lalu

    Hello. How are you? I am interest in your project. Excuse me, but can you check my profile? If you hire me, then your project will be completed more successfully. Thank you. Regards. Julia

    • 5 hari yang lalu

Tunjukkan lebih banyak komen

Bagaimana mula dengan peraduan

  • Papar peraduan anda

    Papar Peraduan Anda Cepat dan senang

  • Dapatkan bertan-tan penyertaan

    Dapatkan Bertan-tan Penyertaan Dari seluruh dunia

  • Anugerahkan penyertaan terbaik

    Anugerahkan penyertaan terbaik Muat turun fail-fail - Senang!

Papar Peraduan Sekarang atau Sertai kami Hari Ini!