Convert a X-moving stage to a Z-moving one

Status: Closed
Hadiah: €300
Penyertaan Diterima: 4
Pemenang: geno700

Papan Penjelasan Umum

chongajlo
- 3 bulan yang lalu
Why is it impossible to submit another entry when winner isn't chosen? I have finished my drawings and now I can't submit.
- 3 bulan yang lalu
1. Penganjur Peraduan
  - 3 bulan yang lalu
  in 30days from contest ending, if we don't pick a winner, the award will be split between the submissions considered valid, so it is safer to avoid accepting new entries at any time (..i believe)
  - 3 bulan yang lalu
Penganjur Peraduan
- 3 bulan yang lalu
Hello everyone - by mid next week we will either pick a winner or reject all offers except two, and the two freelancers will split the EUR300 as per Freelancer rules (We have two proposals that are almost equally good). Thank you for your participation in this contest!!
- 3 bulan yang lalu
Yohanesujang
- 3 bulan yang lalu
please check #22
- 3 bulan yang lalu
Penganjur Peraduan
- 3 bulan yang lalu
Dear all,

As we are now almost one day before the contest end, and I see that all submissions are delivering the overall concept of each design, but not the specifics, I would like to ask participants to confirm that the winning offer will be updated with detailed mechanical drawings and full Bill of Materials used.

Unless the above is validated for each design, the design in question will not be evaluated.

Thank you.
- 3 bulan yang lalu
1. chongajlo
  - 3 bulan yang lalu
  I confirm that I will provide detailed drawings in case my design is chosen.
  - 3 bulan yang lalu
Yohanesujang
- 3 bulan yang lalu
please check #17
- 3 bulan yang lalu
1. Penganjur Peraduan
  - 3 bulan yang lalu
  I did and provided comments
  - 3 bulan yang lalu
geno700
- 3 bulan yang lalu
cost limit ? /size limits ?// max linear motion bearings ?/// max z axis guiding bearing ? //
- 3 bulan yang lalu
1. Penganjur Peraduan
  - 3 bulan yang lalu
  no such limitations at this phase.
  However, smaller and lower costs designs will of course win extra evaluation points
  
  Z axis is expected to move 3-6mm
  - 3 bulan yang lalu
Penganjur Peraduan
- 3 bulan yang lalu
The motor can be installed in an angle, but its lift force should not exceed 1.5N
- 3 bulan yang lalu
Penganjur Peraduan
- 3 bulan yang lalu
Please make sure your parts correspond to actually available ones and keep track of overall BOM cost
Preferred supplier: MISUMI, but can work with others too
- 3 bulan yang lalu
chongajlo
- 3 bulan yang lalu
1) What is mounted on the upper surface? Are the vertical guides I installed getting in the way of something?
2) While moving along Z axis, how rigid should X position be?
3) What distance along the Z axis should the stage traverse?
4) Since submission is JPG file do you need only a screenshot of the 3d model to see the concept or do you need drawings for each part and subassembly?
- 3 bulan yang lalu
Lihat 1 mesej lagi
1. chongajlo
  - 3 bulan yang lalu
  1) You wrote that we should convert existing stage you have on stock. What exactly do you have on stock? Just the linear engine or upper and lower body as well?
  2) What material are the upper and lower body made of?
  3) Can we make alterations to the upper and lower body (drill holes, mill grooves etc)?
  4) What is the linear engine traverse length? Do you want the stage to be raised 5 mm in it's furthest position or is that not important?
  5) Can you share the linear motor designation, in case I need more info on it?
  6) In case the entire stage you have on stock is purchased, can you share it's designation?
  7) How many movements are we talking about? Will it go up and down a thousand times a day or ten times a day?
  - 3 bulan yang lalu
2. Penganjur Peraduan
  - 3 bulan yang lalu
  1) you can use any parts you want - just keep track of your BOM
  2) No big restrictions - Aluminum is ok, but can work with others. Just keep it light
  3) Yes
  4) 50mm X travel, 5mm Z would be ok
  5) Please use the model (.step file) as a reference - it is very accurate. Is there a specific parameter you need?
  6) not sure what you mean by 'the entire stage'
  7) full stroke maybe 5-10times a day - small movements (
  - 3 bulan yang lalu
geno700
- 3 bulan yang lalu
more info needed best wishes !
- 3 bulan yang lalu
1. Penganjur Peraduan
  - 3 bulan yang lalu
  Please comment specifically on what info you need
  - 3 bulan yang lalu
sharukhansari943
- 3 bulan yang lalu
Please describe clearly what you need???
- 3 bulan yang lalu
1. Penganjur Peraduan
  - 3 bulan yang lalu
  Please comment specifically on what info you need
  - 3 bulan yang lalu
chongajlo
- 3 bulan yang lalu
Hi,
I'm not completely sure what you need. If the lower body moves along the X axis then the upper body will move along the Z axis provided it's fixed along the X. Thus, the stage is converted. Would you like someone to elaborate on this, define materials, linear guides, etc, or come up with another solution?
- 3 bulan yang lalu
1. Penganjur Peraduan
  - 3 bulan yang lalu
  Hello Bojan, the example idea offered is just a concept - as you mentioned for example, X axis needs to be fixed. Linear guides ideally, wont be needed.
  - 3 bulan yang lalu