3D Print Files (STL) for possible ongoing work

  • Status: Closed
  • Hadiah: $100
  • Penyertaan Diterima: 10
  • Pemenang: Ayham4CG

Ringkasan Peraduan

The first project is a double clamp (Vice) designed to be used to clamp lumber (2X4) to 1-1/4" square railings and other similarly sized attachment areas. It must incorporate SAE bolts, nuts, etc for additional strength. Bonus if the files can be iterated a few times using FEA methods for more strength with Tough PLA or Carbon Fibre blended filaments to be used in FDM 3D printers.

Kemahiran Disyorkan

Maklum Balas Majikan

“The files look like they will work for 3D printing; the extra part (that I didn't think to ask for) that was very good is that he included both an animation of the assembly as well as a simple bill of materials for the added fasteners required.”

Gambar Profil Brennan199, Canada.

Penyertaan teratas dari peraduan ini

Lihat Lebih Banyak Entri

Papan Penjelasan Umum

  • rashid78614
    rashid78614
    • 1 bulan yang lalu

    working

    • 1 bulan yang lalu
  • aanyuliansyah87
    aanyuliansyah87
    • 1 bulan yang lalu

    Please wait my entry

    • 1 bulan yang lalu
  • Ayham4CG
    Ayham4CG
    • 1 bulan yang lalu

    working on it..

    • 1 bulan yang lalu
  • Brennan199
    Penganjur Peraduan
    • 1 bulan yang lalu

    UPDATE - Please include the STL file with your entry along with the original 3D file. I'd like to check the winning candidates to make sure the file works in Cura.

    • 1 bulan yang lalu
  • Brennan199
    Penganjur Peraduan
    • 1 bulan yang lalu

    ANS: V-Grooves and other types of channels are common in vices. As long as it's not an angle greater than 45 degrees it should print well using a standard 3D FDM printer without using support materials.

    • 1 bulan yang lalu
  • macene16
    macene16
    • 1 bulan yang lalu

    What is the purpose of the V groove?
    Also I think your second section view have some missing details or wrong.
    Please share similar image or exact hand sketches.
    Regards

    • 1 bulan yang lalu
  • Brennan199
    Penganjur Peraduan
    • 1 bulan yang lalu

    INSPIRATION - Here is a one piece solid hobby vice (too small for this contest, and not an assembly), but, you can see how it could work if making it larger, using off-the-shelf SAE bolts and nuts, and upgrading the design of the thin sections to be more robust. REF: https://www.walmart.com/ip/Mini-Bench-Vise-Table-Swivel-Lock-Clamp-Vice-Craft-Hobby-Repair-Tool-Jewelers-S2/921247690?athbdg=L1700

    • 1 bulan yang lalu
    1. GTLM
      GTLM
      • 1 bulan yang lalu

      Now I understand what you tried to convey in the drawings. Thank you very mcuh!

      • 1 bulan yang lalu
  • GTLM
    GTLM
    • 1 bulan yang lalu

    Greetings. Can you please attach more descriptive drawings? From the one you attached it's not clear (at least not for me) what you're looking for. Thanks.

    • 1 bulan yang lalu
    1. Brennan199
      Penganjur Peraduan
      • 1 bulan yang lalu

      Hi Leonel - I could but then I wouldn't have a reason to hold a contest, I'd just design it myself. Some of the questions and pictures submitted so far may help you figure out a good way to tackle this. All the best!

      • 1 bulan yang lalu
  • jilvanjil6
    jilvanjil6
    • 1 bulan yang lalu

    hi I've seen the description of the project you are working on. but in the design sketch file that you attached, I don't understand the function of the components behind the clamp area.

    • 1 bulan yang lalu
    1. Brennan199
      Penganjur Peraduan
      • 1 bulan yang lalu

      Hi Jilvan - Good question! If it's the side view (the right side of the drawing) then it's just two tabs for possibly mounting the top part of the vice directly to a surface (it doesn't HAVE to have this, but if they werea bolt on part/upgrade, even better). If it's the left side of the drawing, in front of the clamp is a double nut (one possible option) and at the back of the top clamp its a captured nut inside a two part jaw. If going this route (again, just one possible way to make it work) I'd suggest connecting the jaw using smaller nuts and bolts. This design allows you to clamp and unclamp without losing the large threaded nut inside the jaw, but, there might be a better way I've not thought of yet. Hope that helps you and everyone else out.

      • 1 bulan yang lalu
  • MRGRAPH003
    MRGRAPH003
    • 1 bulan yang lalu

    ch you mean a copy or similar as this PANAVISE
    Aluminum Vise Head, V-Grooved Jaw Face, Ribbed Neoprene Jaw Material, 1 7/8 in Jaw Width
    source https://www.grainger.com/product/40N558?ef_id=Cj0KCQiAkZKNBhDiARIsAPsk0WhoAYbR6BTYokI21VLUGG3cThYV2TCKPV0LUZwU8bUpHaXv_CvU2DMaAu_xEALw_wcB:G:s&s_kwcid=AL!2966!3!264955915874!!!g!438993529105!&gucid=N:N:PS:Paid:GGL:CSM-2295:4P7A1P:20501231&gclid=Cj0KCQiAkZKNBhDiARIsAPsk0WhoAYbR6BTYokI21VLUGG3cThYV2TCKPV0LUZwU8bUpHaXv_CvU2DMaAu_xEALw_wcB&gclsrc=aw.ds or other ones we have here in the U.S.A?

    • 1 bulan yang lalu
    1. Brennan199
      Penganjur Peraduan
      • 1 bulan yang lalu

      The top part of this one could be adapted for printing: https://www.grainger.com/product/PANAVISE-Steel-Vise-Head-40N560?opr=APPD&analytics=altItems_40N558

      • 1 bulan yang lalu
  • Brennan199
    Penganjur Peraduan
    • 1 bulan yang lalu

    OK- Clarifications. It is to be 3D Printed, therefore it must be able to be printed in parts, and assembled as a working, functional double vice. If you know anything about 3D printing, you know that you can embed or add parts (metal parts, like SAE nuts and bolts) to make the piece stronger and more functional. A typical inexpensive printer (Like the Creality Ender 3) can only print inside a 220mm X 220mm area at about 250mm high. My preference is to use the SAE bolts/nuts/etc. as not only a method of holding it together and making it stronger, but also as the main threaded part of the slide. The particular Panavise Ramon G chose (in comments) is not a great example, but it's larger version might be a good start for the top vice only, which must open up wide enough to clamp to a rough 2X4 (the 4" is actually 3.785" or less, so if it doesn't ACTUALLY open up to 4" I'll be ok with that since technically it will clamp to a 2X4). The lower vice must fit over a 1.25" square rail.

    • 1 bulan yang lalu

Tunjukkan lebih banyak komen

Bagaimana untuk mulakan dengan peraduan

  • Siarkan peraduan anda

    Siarkan Peraduan Anda Cepat dan mudah

  • Dapatkan berjuta penyertaan

    Dapatkan Bertan-tan Penyertaan Dari serata dunia

  • Anugerahkan penyertaan terbaik

    Anugerahkan penyertaan terbaik Muat turun fail - Mudah!

Siarkan Peraduan Sekarang atau Sertai kami Hari Ini!