Do some simple 3D Modelling - Drawings For Manufacturer

  • Status: Closed
  • Hadiah: $100
  • Penyertaan diterima: 5
  • Pemenang: ARTandFASHION

Keterangan Peraduan

I need a simple but functional device that will hold 3 double sided screwdriver bits and a bit tip holder OR 4 double sided screwdriver bits. It must fit either or. The purpose of this will be for the holding device along with the 3 sided bits and bit tip holder to fit within a tube that measures 15mm wide. I would like to make it as slim as possible and even for it to measure 14mm in width. It also cannot exceed 51mm in height. Again, the device does not need to be overly complicated or great looking. The simplicity (usability) and function is most important.

The holding device is made of plastic. There can be a small magnet built in to the holding device if it will help to hold the pieces in the device. The bit tip holder is also magnetized and the device will be inserted into a metal tube. The device should make it so that it is difficult for anything to "stick" to the sides of the tube because of the magnet.

The bits are 50mm in length. The bit tip holder is also 50mm in length. I need the modeling to show how the bits and bit tip holder fit within the device. These bits are standard hex shape and I will want the measurements of 50mm height and 6.35mm width to be shown in the drawing for the manufacturer but the tips of the drivers do not need to be drawn out. As long as they look the park that is fine. For the bit tip holder I will want it to be drawn out in its entirety keeping in mind that once again the hex shape is the standard like the bit measurements. The shank or "post" will be 10.5mm. The holding piece will be 39.55mm long for a total of 50mm total height. The width at the "post" or shank will be the standard 6.35mm and I will want the width of the bit holder section to be drawn out.

Please let me know if any questions! The drawings must be finished to submit to manufacturer within 1 day of the ending of the contest. The contest will run for 3 day only. I will post it for three days but I will want it as soon as possible. The first to create the finished drawing will win the contest. This is an emergency situation for submission to this manufacturer. Please see the pictures attached. Thanks!

Kemahiran-kemahiran Cadangan

Maklum balas Majikan

“Very good and very quick with design. Knew what I was talking about simply from a description and designed it. Thank you! Will try to work with you again.”

Gambar Profil jpalace82, United States.

Penyertaan teratas dari peraduan ini

Lihat Penyertaan Lain

Papan Penerangan Awam

  • dima819
    dima819
    • 2 tahun yang lalu

    I will try provide concept tomorrow. Today i haven't time :(

    • 2 tahun yang lalu
  • jpalace82
    Pemegang Peraduan
    • 2 tahun yang lalu

    Hello to anyone who is viewing this! There seems to be some confusion and I can certainly understand since I am just trying to verbally explain what I have looking for. I have attached two pictures. For the first one labeled "Double Sided Bit" there are 3 of these that will be held by the device. For the picture labeled "Bit Tip Holder" there is one of these that will be held by the device. Which means, there are a total of 4 items that will be held by the device. The device is not pictured. That is what I need your help with! The device will hold all 4 of these items and fit within a circular tube that is no larger than 15mm on the inner diameter. The rest of the measurements are above. Thank you!!!

    • 2 tahun yang lalu
  • luisss749
    luisss749
    • 2 tahun yang lalu

    Hi wich kind of magnet are has in mind? about the bit holder, which is the diameter of the holder section?

    • 2 tahun yang lalu
    1. luisss749
      luisss749
      • 2 tahun yang lalu

      the tube which receive the assembly is round section?, the height of the device is 51 mm max, but the height of the assembly is limited to this same heigh?

      • 2 tahun yang lalu
    2. jpalace82
      Pemegang Peraduan
      • 2 tahun yang lalu

      The tube is perfectly round. The height of the tube is actually 55mm. But I prefer to have some buffer and this also may go in a plastic tube that then is inserted into the metal tube, Make sense? I know this sounds odd but this is a small part in a bigger picture. Good questions!

      • 2 tahun yang lalu
  • jpalace82
    Pemegang Peraduan
    • 2 tahun yang lalu

    Try this everyone. This is not exactly what I want but it does demonstrate a "holding device"...again I want to keep it slim, basic, and functional... http://www.alibaba.com/product-detail/Top-quality-professional-ningbo-factory-useful_60313844758.html?spm=a2700.7724838.35.14.ZPIwpM

    • 2 tahun yang lalu
  • dima819
    dima819
    • 2 tahun yang lalu

    Hello! What format you need in finish?

    • 2 tahun yang lalu
    1. dima819
      dima819
      • 2 tahun yang lalu

      It would be very helpful. And would reduce time the flight of thought:)

      • 2 tahun yang lalu
    2. jpalace82
      Pemegang Peraduan
      • 2 tahun yang lalu

      I really can't find anything. That is what has made this difficult for the manufacturer. The parts are easy for them. The holder concept is very difficult and there is also a language barrier. I will keep looking but if you are interested in the project maybe you can start with something and I would be happy to collaborate. I actually prefer that anyways so that we can work together on it.

      • 2 tahun yang lalu
  • Cube88
    Cube88
    • 2 tahun yang lalu

    Hello. Do you want pencil drawing or 3D modelling?

    • 2 tahun yang lalu
    1. jpalace82
      Pemegang Peraduan
      • 2 tahun yang lalu

      Hello! 3D Modeling Please

      • 2 tahun yang lalu

Tunjukkan lebih banyak komen

Bagaimana mula dengan peraduan

  • Papar peraduan anda

    Papar Peraduan Anda Cepat dan senang

  • Dapatkan bertan-tan penyertaan

    Dapatkan Bertan-tan Penyertaan Dari seluruh dunia

  • Anugerahkan penyertaan terbaik

    Anugerahkan penyertaan terbaik Muat turun fail-fail - Senang!

Papar Peraduan Sekarang atau Sertai kami Hari Ini!