Antenna designpekerjaan

...are in a bag. Bluetooth Module: A Bluetooth module such as the HC-05 or HC-06, ensuring compatibility with the Arduino board for wireless communication to a computer or smartphone. Power Supply: UHF RFID readers often require more power. A robust power source is necessary, such as a higher-capacity LiPo battery or a dedicated power adapter. Antenna for UHF RFID Reader: UHF RFID operations require an appropriate antenna. The size and type of the antenna will depend on the desired reading range and the specific UHF RFID module you are using. Connecting Wires: Appropriate cables or jumper wires to connect the UHF RFID reader, Bluetooth module, and Arduino board. UHF RFID Tags: UHF RFID tags compatible with your reader, for testing and deployment purposes. Software Requ...

I am in search of a seasoned RF engineer with experience in 3D modeling and simulation for the design and development of an omnidirectional antenna intended for signal transmission (television, radio, etc.). Key tasks include: • Analysis of antenna requirements for signal transmission • 3D antenna design and development • Testing and troubleshooting Skills Required: • Expertise in RF engineering • Proven experience with 3D design and simulation of antennas • Comprehensive understanding of RF testing and troubleshooting methodologies • Previous experience in signal transmission- specifically for television and radio. This is not just an antenna design job, this is a chance to create something...

I am seeking an experienced professional to design, and implement a setup that would allow for the display of GPS antenna signals on an oscilloscope. The aim is to conduct an experiment to measure the speed of light. Key responsibilities include: - Design and build a system capable of measuring, displaying and analyzing GPS antenna signals on the oscilloscope. - Ensure that the system is able to demonstrate a 10ns shift whenever the antenna is raised or lowered by 10’. Ideal freelance candidates will have: - Proficiency in the use of oscilloscopes and other related equipment, - A sound understanding of signal processing, - Knowledge in the physics of light and GPS technology, - Strong problem-solving abilities and the capacity to work independent...

I'm seeking an expert designer to build an array antenna with specific attributes: - The design is specified in the IEEE publication attached to this project. - Intended for high-speed communication applications - Must function within the microwave frequency range (L, S and X) - Dual-pol design - SEE ATTACHED IEEE PUBLICATION FOR FULL SPECS. Ideal Candidate: - Proficiency in RF engineering and antenna theory - Experience designing microwave antennas - Skilled in simulation software (e.g., CST, HFSS) - Ability to prototype and test designs - Strong problem-solving skills I value precision and efficiency, hence I'm looking for a freelancer who can deliver high-quality work within the set deadlines. Your work will empower communication technologies. ...

Sila Dafter atau Log masuk untuk melihat butiran.

I need two infographics that will used to illustrate the subject matter on this blog post (please review the blog post to get ideas for your infographic: I will choose two winners of the contest: 1. One winner for Antenna Cable Installation 2. One winner for Antenna Cable Management Include the logo of Data Alliance (see: ): Small, and placed at or near the bottom (the logo should not dominate the graphic, but rather should be a more discreet aspect of the graphic). Include a small, discrete line of copyright text at the bottom: Copyright Data Alliance Inc. All rights reserved. Please double-check your entry for spelling errors before submitting it. In the file handover:

Project Description: I am looking for a skilled 3D artist to create a rendering of an antenna with a desert background. The rendering should be moderately realistic with some details, capturing the essence of the antenna in a visually appealing manner. I need two designs for two antennas one thisk and one is thin. both are 80 cm diameter The 1st antenna is 30 cm thick The second is 8 cm diameter color: tan standing on triapod orientation 30 cm upward background: desert similar to the image in teh website below I need teh design to be readable by solidworks

...3D printed model. Any large STEP files of the final product will need to be broken up into two smaller STEP files so they can individually fit on the 3D Print bed. The printing area is 10"x10"x10". Please refer to image 1. This images shows a speaker grill for a car dash that sits inside of a bezel. We need to change the grill into a 3D dome that will hold 3 satellite antennas. That specific antenna dims will be provided later. THE OUTER PERIMETER OF THE STEP FILE NEEDS TO EXACTLY MATCH THE OUTER PERIMETER OF IMAGE 1. AGAIN, THE OUTER PERIMETER MUST EXACTLY MATCH THE IMAGE. Image 2 shows the speaker grill set into its bezel. In this image, the bezel is INVERTED, so it is showing the bottom side. Image 3 shows the underside of the bezel, and how the perimeter of...

2. System Overview The system shall consist of the following key components: * Multi-antenna RFID reader(s) capable of simultaneous tag reading. * RFID tags compatible with the reader's frequency and protocol. * Antenna configurations optimized for the application. * Reader software for tag data processing and management. * Integration with existing systems, if applicable. 3. Functional Requirements 3.1 Tag Reading * The system shall be capable of reading a minimum of 8 RFID tags simultaneously within a specified coverage area. * RFID tags shall be read without significant interference or collision. * The system shall support tag reading at a rate of at least 50 tags per second. * The system shall provide accurate and real-time data on the tags�...

Project Description: PCB Design I am looking for an experienced PCB designer to help me with a moderately complex project. I need a HAT for a Raspberry Pi Zero, the HAT will need to have a GPS chip and communicate with the raspberry pi via UART. The pcb will also need a connector for the antenna connection. Components: - NEO-M9N-00B GPS or similar GPS module PCB Layers: - I would like the PCB to have double layers. Skills and Experience: - Strong proficiency in PCB design - Experience with designing moderately complex PCBs - Knowledge of various components and their integration into PCBs - Ability to suggest and select appropriate components based on project requirements If you have experience in PCB design and are ready to tackle this project, please s...

...System Design Service with Specific Requirements and Flexible Deadline We are seeking a skilled and experienced RF hardware designer to provide RF system design services for our project. The ideal candidate will have expertise in RF system design and be able to meet our specific requirements. We are looking RF hardware design service and we already have a schematic design but it need some rectifications. Our requirement is to correct schematic and generate the Gerber file . for example You need to fix the transmitters heads and you only need to by or add frequency generator software and a little bit of software that only need for data saving, data control, and radar identification. Specific Requirements: - We have detailed specifications and re...

Enclosure Design for Electronics with Smoke Detector Skills and Experience: - Experience in designing enclosures for electronics - Knowledge of smoke ventilation systems Requirements: - Design an enclosure for smoke detector - To be mounted on the ceiling with an attached antenna - No specific size or shape is provided, but there are some specifications - Ensure the enclosure is suitable for electronic components - Consider the need for shock resistance and waterproofing, if applicable Note: This project does not require outdoor or industrial enclosure design.

RFID and NFC Reader for Add-On Application - I am in need of a reader that can support both RFID and NFC technologies. - The intended use of the reader is for an add-on application. - I require only one reader for this project. Ideal Skills and Experience: - Experience in developing RFID and NFC readers. - Knowledge of inventory tracking, access control, and payment systems. - Ability to integrate the reader into an existing system. - Strong understanding of RFID and NFC technologies. - Familiarity with industry standards and protocols. - Proficiency in programming languages used for reader development. - Attention to detail and ability to troubleshoot and resolve technical issues.

I am looking for a skilled freelancer who can develop an embedded NFC reader and antenna for my project. The intended application of this NFC reader and antenna is to be used as an add-on for a security system. Skills and Experience: - Experience in developing embedded systems and NFC technology - Knowledge of antenna design and integration - Familiarity with security system applications - Ability to meet deadlines and deliver the project within a month.

I will choose multiple winners of this contest (it may be many). Each winner gets their own feedback. This contest will be open until late January or February so that you can take as much time as you need to make great graphics and multiple versions. Make an infographic about MHF4 connectors. MHF4 is a type of connector for antenna cables. The following ideas are for you to create the best infographics on this subject: There are multiple variations and you can focus on one variation, or make a composite of multiple variations: All of these version types are good: Version/variation #1. Show a MHF4 connector on a cable (black cable) and show a jack on a PCB board. Version/variation #2. Show a MHF4 insertion tool (see on ) with the infographic showing the proper installation

I am looking for a freelancer to create a Full Materials Declaration document for an antenna with cable and connector. The purpose of this document is to provide transparency for our customers. Skills and experience needed: - Knowledge of regulations and compliance related to materials declaration - Experience in supply chain management - Strong attention to detail I will provide documentation of all the materials (it's five documents). The freelancer will need to review and organize this information into a Full Materials Declaration in Word format. The document should provide a detailed description of each material used in the antenna with cable and connector. This project requires a freelancer who can accurately and comprehensively describe each material, ensurin...

Design a Qi compatible wireless charging receiver (RX) unit for 10 - 15W. - receiver antenna coil must be small, either 1) 24mm diameter or less, or 2) 20mm x 40mm or less - 10W+ receiving power at 6mm - when possible for capacitors and resistors use 0603 (metric) size parts - use parts available for purchase on digikey or mouser - provide 2.54mm header for external connection to +/-

I am seeking a freelancer to assist in setting up Sllurp with the Zebra FX9600 reader to capture tag events. The objective is to transmit data to a specified URL each time a new tag is identified, including the reader's IP, antenna ID, tag details, and timestamp. The completion timeframe is 2-3 days, and remote access to the reader will be provided. Key Requirements: Integration of the configuration into my preferred platform. Anticipated tag volume is below 1000. Desired Skills and Experience: Proficiency in configuring Sllurp with the Zebra FX9600 reader. Knowledge of RFID technology and expertise in tag event reading. Familiarity with various integration platforms.

RFID Reader Design a RFID Reader circuit for the PN532. Support I2C @ 3.3V. The antenna size should be 12 x 12 cm. I am in need of an experienced Electronic engineer who can develop an RFID reader that utilises the PN532 chip. Experience with the PN532 is preferred. Experience with designing RFID antennas is required. Please also explain your design, particularly how the proper capacitance is achieved. - Purpose: The primary function of this RFID reader is to identify object presence. The objects in this case are "custom devices". Sensitivity and accuracy are therefore paramount. - Design Requirements: The reader must integrate a 12 x 12 cm antenna to fit within the confined space of the unit. The core of this project is the implementation o...

...the scanned mower (geometry of the tank should be largely retained) - Next step: moulds for tower, vessel and chain created ---> ensure that the cast models can be removed from the mold again (detail features of the tank can be adjusted to ensure propper demold) - Ensure dimensions (observe tower dimensions after thermoforming -- should be able to be inserted into the opening of the vessel) - Antenna, radar dish and gun barrels need not be included in the mold. These are produced later via 3D printing - Model can stop approx. 5 cm before the floor Preferred Material: - I would prefer the cast mold to be made using 3D printing technology. Thererfore no shells, only solid construction. Desired Size: - The desired size of the cast mold should be able to fit on a 3D scanned rob...

Moodlebox () is a Raspberry Pi projects which runs Moodle on a Raspberry Pi board (). Moodlebox broadcasts a wi-fi sign...devices. Desired outcomes: The Moodlebox cluster must: 1. be able to handle at least 75 simultaneous connections with video being streamed on up to 40 of those connections. 2. be customisable. All customisations that are possible on the regular Moodle installation must be possible on the Moodlebox cluster. 3. be able to have a wi-fi antenna connected to it to increase the range that the wi-fi signal from the Moodlebox is broadcast. The selected consultant will design the setup and guide someone remotely to setup and test the Pi cluster setup and installation of Moodlebox on the cluster.

Please contact for more details about the design for a stowable yet beam scanning antenna for high power microwave applications.

Project: CST Antenna Simulation Steps for Installed Performance I am looking for a skilled professional to show me step by step in a word document with screenshots, how simulation steps should be done for a basic monopole antenna installed on an airplane or any other platform, automotive or something else with hybrid solver. He/she will show in the word document; -how the platform(airplane/automotive etc) CAD file imported, -how an antenna is put on the top of the platform -then simulation steps for hybrid solver solution step by step, so every mouse click before running the simulation must be shown -Rather than an antenna design project, this will be only informative document for me as a hobbyist. Therefore, you are free to choose any antenna w...

Project Title: SIMCOM A7672S RF antenna - Network Issue Resolution I am seeking a freelancer with expertise in RF antennas and network troubleshooting to assist with resolving a network issue we are facing with the SIMCOM A7672S RF antenna. The issue is related to signal interference when using IoT/Normal SIM cards for communication. Network Issue: - The specific problem we are experiencing is signal interference. Interference Conditions: - The interference occurs constantly, without any specific conditions. Steps Taken: - We have already tried different SIM cards in an attempt to resolve the issue. Ideal Skills and Experience: - Extensive knowledge and experience in RF antennas and network troubleshooting. - Familiarity with SIMCOM A7672S RF antenna and its commu...

I am seeking a professional firmware engineer to help me create an ELD (Electronic Logging Device) with customizable options based on specific requirements. J1939 device specifications - WiFi 801.11b/g/n up to 150Mbps and simultaneous AP and Station modes - Bluetooth 4.2 Class 1 supporting BR/EDR and LE dual-mode - Multi-constellation GNSS receiver with built-in high-gain antenna - High-efficiency switching power supplies for low temperature operation - Over-, under-, and reverse-voltage protection exceeding automotive standards - ESD protection exceeding automotive standards - Full-color RGB LED for status indication - Dual-core 32-bit Tensilica processor at 240MHz - Built-in J1939 Type II 9-pin connector supporting both new and legacy vehicles - Physical layer and protocol auto...

I am seeking a skilled freelancer to assist with the development of an RF based on SDR prototype. The purpose of this project is to create a functional prototype that operates within the S and C band frequencies. The desired operating frequency range for the SDR should be between 1-6 GHz with Tx upto 2 KW with sdr based phased erray antenna for Tx. Ideal Skills and Experience: - Strong background in RF engineering and SDR development - Experience with prototype development and testing - Knowledge of the S and C band frequencies - Proficiency in programming languages commonly used in SDR development

Model 4 pulsed threat radars with operating frequencies varying between 4-8 GHz with the EW Self-Protection System's jamming system on a fighter aircraft with an RCS of 12 m2 . Design the antenna for the jammer separately in MATLAB application and use the pattern of this antenna in the simulation. Perform a MATLAB simulation in which the detection (burn-through) distance of the J/S and the fighter is calculated for the jamming of the EW Self-Protection System at three different powers for each radar.

I am seeking a skilled freelancer to design and create a small electronics enclosure for my project. The enclosure should have the following specifications: Size Requirement: - The enclosure will be small, with dimensions max 100 x 60 x 10 mm - See pictures for first design draft Intended Use: - The enclosure will be for electronic sensors inside shipped goods. Can get cold and hot but not wet. - There will be a battery cover to easily change batteries - The design should include a low cost 4-wire connector that will allow the device to be electrically connected to a docking station. The docking station will be designed later, based on this design. - It should either be a cut-out for GPS antenna or a thicker enclosure to accommodate it. The ante...

I have very limited C# experience. I need help configuring a running copy of on 2022 Visual Studio 17. I plan on using some HID relays to control some Amateur radio antenna switches. K7OGW

----------------------------------------------------------- I WONT ANSWER "WHATS YOUR BUDGET?" QUESTION PLEASE SET A REALISTIC BID ------------------------------------------------------------ I have got a custom ESP32 board which has an onboard ceramic antenna. I need help to get a stable WiFi connection. I think the anntenna circuit needs to be adjusted.

Make an infographic about the distinctions between RG-174 and LMR-100 coaxial cable types. LMR-100 and RG-174 are coax types for antenna cables. The infographic can show some or all of the following information: 1. The differences in attenuation (signal loss) for each of the two types. 2. The bend radiuses of each of the two types 3. Diameter / thickness of each of the two types. 5. Shielding characteristics of each 6. Any other distinguishing information that you can find that makes the graphic more interesting is fine. I will choose some winners that are more complex and some that are less complex. 7. Maximum frequency range of each type (max for LMR-100 is 6 GHz). I will choose multiple winners of this contest (it may be more than five). Each winner gets their own feedback. Inc...

Hi I need to include a custom antenna Bluetooth (2.4 Ghz) in my current of PCB. The antenna will be connected to connector IPX-V1 + Wire. I dont know if the antenna could be ceramic or printed. The propousal of antenna must be tunning to 50 Ohm and SWR < 2.0 I attached the PCB form factor, and the zone were i need the antenna. Thanks. Ricardo

I need a custom PCB that uses: - HDC1080 - nRF52810 - 2450AT42A100 antenna - CR2450 battery (3v) - With holder which will be THT, so you have the components on one side and the battery on the back. I’m going to be using a TC2050-IDC-430 + SEGGER J-Link to flash the device - so will need some pogo pins which can be used to flash the device.

I am looking for a skilled CAD modeler who can assist me with creating a 3D model of a radio antenna, based on detailed specifications. The CAD model will be used for design analysis, leading to manufacturing. CAD and electrical engineering skills are desired. If you have the necessary skills and experience, please submit your proposal.

...Ideal skills required: 1. Carrier board for Jetson Orin Nx module 2. Carrier board should have lock type connector provision to plug in the “Jetson Orin Nx” module externally 3. SSD/eMMC Interface. Schematic should consider locks types connector provision to plug in the SSD externally. appropriate part to be selected 4. BLE Module Interface. On board support for selected BLE Module (inbuilt antenna), appropriate part to be selected 5. Type-C USB host Interface. On-board USB C type connector provision 6. RTC - On board RTC support 7. Microphone: Omni directional Noise cancellation microphone array with > 20 DB SNR at 5m range under wind noise condition 8. Audio Jack: Interface for connecting external headphone (2 in 1 - mic and speaker) 9. Speaker: 2Watt Speaker...

I need to develop a compact reader for Mifare Classic or Mifare Ultralight. The board width is 15mm, antenna diameter is 15mm. The device should read password-protected areas and send them to the host via RS485 interface. I need schematics, a PCB, and a working prototype. 3-4 weeks deadline. Please see the attached description.

I will choose multiple winners of this contest (it may be many). Each winner gets their own feedback. This contest will be open until around Dec 3 so that you can take your time to make great graphics and multiple versions. Make an infographic about connectors. is a type of connector for antenna cables. The following ideas are for you to create the best infographics on this subject: There are multiple variations and you can focus on one variation, or make a composite of multiple variations: All of these version types are good: Version/variation #1. Show a connector on a cable (black cable) and show a jack on a PCB board. Version/variation #2. Show a insertion tool (see on ) with the infographic showing the proper installation of a connector on a jack:

I will choose multiple winners of this contest (it may be more than five). Each winner gets their own feedback. Make an infographic about the distinctions between LMR-100, LMR-200 and RG-58. LMR-100, LMR-200 and RG-58 are coax types for antenna cables. The infographic can show some or all of the following information: 1. The differences in attenuation (signal loss) for each of the three types. 2. The bend radiuses of each of the three types 3. Diameter / thickness of each of the three types. 5. Shielding characteristics of each 6. Any other distinguishing information that you can find that makes the graphic more interesting is fine. I will choose some winners that are more complex and some that are less complex. 7. Maximum frequency range of each type (max for LMR-100 and LMR-200 ...

I will choose multiple winners of this contest (it may be more than five). Each winner gets their own feedback. Make an infographic about the distinctions between LMR-200 and RG58. LMR-200 and RG58 are coax types for antenna cables. The infographic can show some or all of the following information: 1. The differences in attenuation (signal loss) for each of the two types. 2. The bend radiuses of each of the two types 3. Diameter / thickness of each of the two types. 5. Shielding characteristics of each 6. Any other distinguishing information that you can find that makes the graphic more interesting is fine. I will choose some winners that are more complex and some that are less complex. 7. Maximum frequency range of each type (max for LMR-200 is 6 GHz). RG-58 has a single tinned ...

I will choose multiple winners of this contest (it may be more than five). Each winner gets their own feedback. Make an infographic about the distinctions between LMR-100 and RG174. LMR-100 and RG174 are coax types for antenna cables. The infographic can show some or all of the following information: 1. The differences in attenuation (signal loss) for each of the two types. 2. The bend radiuses of each of the two types 3. Diameter / thickness of each of the two types. 5. Shielding characteristics of each 6. Any other distinguishing information that you can find that makes the graphic more interesting is fine. I will choose some winners that are more complex and some that are less complex. 7. Maximum frequency range of each type (max for LMR-100 is 6 GHz). Include the logo of Data...

I will choose multiple winners of this contest (it may be more than five). Each winner gets their own feedback. Make an infographic about the distinctions between LMR-100 and RG58. LMR-100 and RG58 are coax types for antenna cables. The infographic can show some or all of the following information: 1. The differences in attenuation (signal loss) for each of the two types. 2. The bend radiuses of each of the two types 3. Diameter / thickness of each of the two types. 5. Shielding characteristics of each 6. Any other distinguishing information that you can find that makes the graphic more interesting is fine. I will choose some winners that are more complex and some that are less complex. 7. Maximum frequency range of each type (max for LMR-100 is 6 GHz). RG-58 has a single tinned ...

Make an infographic about the specifications of 0.81mm coaxial cable. I will purchase about 4 or 5 of the entries from this contest. Each winner gets their own feedback. The purpose of the coax is for cables, and it is good to mention The infographic can show some or all of the following information: 1. The attenuation (signal loss) for various frequencies. 2. Shielding characteristics and specifications. 3. The bend radius. 4. Diameter / thickness. 5. Compare to 1.13mm coax: We only need one version like this (don't do this for all versions) Any other distinguishing information that you can find that makes the graphic more interesting is fine. I will choose some winners that are more complex and some that are less complex. Title of the graphic can be some variation on one o...

...infographic about the torque ratings of RP-SMA connectors. Ideas for you to create the best infographics on this subject: All of these version types are good: Version #1. Show both the male and female versions of RP-SMA connector Version #2. Show the Male connector only Version #3. Show the Female connector only Version #4. Show RP-SMA connectors on a cable (the connector would be on a black coaxial antenna cable) Don't show the panel-mount type of RP-SMA connector. Include the logo of Data Alliance (see: ): Small, and placed at or near the bottom. Include a small, discrete line of copyright text at the bottom: Copyright Data Alliance Inc. 2024 Please double-check your entry for spelling errors before submitting it. Please submit your file as compressed JPG version. ...

...infographic about the torque ratings of SMA connectors. Ideas for you to create the best infographics on this subject: All of these version types are good: Version #1. Show both the male and female versions of SMA connector Version #2. Show the Male connector only Version #3. Show the Female connector only Version #4. Show SMA connectors on a cable (the connector would be on a black coaxial antenna cable) Don't show the panel-mount type of SMA connector. Include the logo of Data Alliance (see: ): Small, and placed at or near the bottom. Include a small, discrete line of copyright text at the bottom: Copyright Data Alliance Inc. 2024 Please double-check your entry for spelling errors before submitting it. Please submit your file as compressed JPG version. In the file

The microcontroller acts as the initial sensing unit for EEG signals. Once these are detected, a MIMO antenna system is activated to further collect EEG data with higher precision through electromagnetic frequencies. This enhanced data is then sent to a computer running a BCI software that employs a P300-based method to facilitate communication and potentially even visualize what the person is seeing. Here are some considerations for this setup: 1. **Precision**: The use of MIMO for 'virtual electrode placement' could potentially enhance the spatial resolution of EEG readings. 2. **Signal Quality**: MIMO can help improve signal-to-noise ratio, ensuring more accurate and reliable data transmission. 3. **Real-time Processing**: Both P300 detection and image recon...

I will choose multiple winners of this contest (it may be more than five). Each winner gets their own feedback. Make an infographic about the specifications of 1.13mm coaxial cable. The infographic can show some or all of the following information: 1. The attenuation (signal loss) for various frequencies. 2. Shielding characteristics and specifications. 3. The bend radius. 4. Diameter / thickness. 5. Any other distinguishing information that you can find that makes the graphic more interesting is fine. I will choose some winners that are more complex and some that are less complex. Include the logo of Data Alliance (see: ): Small, and placed at or near the bottom. Include a small, discrete line of copyright text at the bottom: Copyright Data Alliance Inc. 2024 Please double-check your ...

I will choose multiple winners of this contest (it may be many). Each winner gets their own feedback. This contest will be open until around Nov 28 so that you can take your time to make great graphics and multiple versions. Make an infographic about MHF4 connectors. MHF4 is a type of connector for antenna cables. The following ideas are for you to create the best infographics on this subject: There are multiple variations and you can focus on one variation, or make a composite of multiple variations: All of these version types are good (your infographic can show one of these variations or a combination of several of them): Version/variation #1. Show a MHF4 connector on a cable (black cable) and show a jack on a PCB board. Version/variation #2. Show aMHF4 insertion tool (see on d...

I will choose multiple winners of this contest (it may be many). Each winner gets their own feedback. This contest will be open until around Nov 23 so that you can take your time to make great graphics and multiple versions. Make an infographic about connectors. is a type of connector for antenna cables. The following ideas are for you to create the best infographics on this subject: There are multiple variations and you can focus on one variation, or make a composite of multiple variations: All of these version types are good: Version/variation #1. Show a connector on a cable (black cable) and show a jack on a PCB board. Version/variation #2. Show a insertion tool (see on ) with the infographic showing the proper installation of a connector

...about the various antenna types. I don't want a composite of a bunch of antennas with no explanation about what type of antenna they are. Please use Data Alliance's antennas () in your Infographic. If you do an infographic about a specific model of Data Alliance antenna, I will very likely buy the graphic (one per model). We have hundreds of models of antennas for IoT applications. Ideas for you to create the best infographics on this subject: All of these version types are good and I will choose a winner from each of these subcategories (or more than one winner from each of these subcategories): Version: Antennas for IoT applications: A composite of various antenna types Version: Antennas for Industrial IoT applications: A composite of v...

...this contest (it may be many). Each winner gets their own feedback. Make an infographic about the materials composition of antenna connector N-Type (N-Type Connector; N-Type Antenna Connector). Type-N is a connector for antennas and antenna cables. The typical materials composition of N-Type connectors is listed on our website: Search data-alliance.net. Ideas for you to create the best infographics on this subject: All of these version types are good: Version #1. Show both the male and female versions of N-Type connector Version #2. Show the Male connector only. Version #3. Show N-Type connectors on a cable (the connector would be on a black coaxial antenna cable) Version #4: N-Type adapter: Sub topics of this: N-male to N-male, N-female to N-femal...