We are a start-up need a programmer or a quick project based on active passive RFID help.
1. QCA7500 SoC 2. No USB, HDMI, Ethernet, Wireless 3. HomePlug Powerline communications only 4. Serial / latch AD1862 DAC 5. PWM Linear hybrid independent, isolated power supplies for DAC, CPU and additional 2x 14v 2.5A output for Amp 6. i2c Auth Chip 7. 44.1 khz sampling freq for Audio 8. Serial / Latch ALSA hardware driver needed Note: I have C code ready for porting.
1. BCM60500 SoC 2. No USB, HDMI, Ethernet, Wireless 3. HomePlug Powerline communications only 4. Serial / latch AD1862 DAC 5. PWM Linear hybrid independent, isolated power supplies for DAC, CPU and additional 2x 14v 2.5A output for Amp 6. i2c Auth Chip 7. 44.1 khz sampling freq for Audio Note: I have C code ready for porting.
Looking for someone to p build a complete working prototype Streaming Receiver homeplug device with a AD1862 DAC 1. BCM60500 SoC 2. No USB, HDMI, Ethernet, Wireless 3. HomePlug Powerline communications only 4. Serial / latch AD1862 DAC 5. PWM Linear hybrid independent, isolated power supplies for DAC, CPU and additional 2x 14v 2.5A output for Amp 6. i2c Auth Chip 7. 44.1 khz sampling freq for ...
We are a l...fourth generation of battery-powered, multi-probe Wi-Fi sensor and we want to add a part-time WLAN software or QA engineer to our embedded engineering team. We are looking for a candidate who has experience with WLAN systems, Linux kernel driver development and who is particularly skilled with WLAN setup, optimization and troubleshooting.
We are looking for a Embedded Firmware Developer with experience in Atmega2560. System has the following sections: 1) Wifi (ESP) 2) Modbus 3) Capacitive Touch Screen (7 Inch) 4) Servo / Stepper Motors Contact us if you are well versed with the firmware development.
This project is to capture the data transmitted and received by an embedded SIM (eUICC). Specifically, we are interested in viewing the data transmitted and received by the "Local Profile Assistant" in the GSMA standard for consumer embedded SIMs. The requirements are to collect a PCAP packet capture and/or IC2/SPI trace of all data transmitted
I have a working springboot application. I want someone to look at the pom and make sure it is correct. 1. Application is on my local windows...springboot application. I want someone to look at the pom and make sure it is correct. 1. Application is on my local windows. 2. deploy and run the application as a service on linux 3. test if it is successful
Hello, I am looking for an embedded designer capable of designing hardware and software. Must be familiar with BMD-350 IC From Nordic Semiconductor.
Like the project title suggests , i have a video which needs to be embedded in an emailer and need a button at the end of the video to redirect users to a different website. Check example over here- [login to view URL] Please reach out only if you know how to do it and can deliver within today itself or
Over time a working spreadsheet has grown to a size where it is not functional. It looks as though the pdf documents keep duplicating when a new version is saved. We would like all pdf's removed.
I need an app capable of extracting the biographic information from a PDF417, (name, gender, address,etc.) this information is not encrypted and it is visible by any Barcode reader app. The challenge is to read the fingerprint information included in the same barcode and compare it to the fingerprint of the person. The device is an android based terminal with a dedicated fingerprint reader FBI cer...
programming has to be done for atmega32 and raspberry pi the project is home automation and the programmer must have knowledge of network communication using rf ( NRF24L01 )the programmer should be able to send and receive messages using RF
Looking for an embedded SW engineer who can make design and modelling of an application at abstract level. I looking to redesign an automotive protocol implementation to a new standard to improve its portability and testability. You should have good skills in: - Expert in C++ design - Expert in UML design - Expert in embedded PC interface protocols
Need to develop a prototype of biomedical device to measure vitals such as blood pressure, pulse, SpO2 and more. WiFi and Ble enabled, battery powered and should have capacitive touch display with a decent UI. You will need to design it around Arm Cortex processor. A RTOS based firmware is preferred. You will need to provide us with detailed schematic, PCB design layout, BOM of device, firmware an...
We are looking for 1 or 2 programmers for an embedded application in C. This project includes the following components: ATMEL328P ESP12 SPI memory, SPI RTC I2C memory Radio modules Need to be very confident in C and have a clear vision of memory management and bootloader. Looking for people who are in China or quite close and available immediately
I need a responsive web-based application, for health, live chat support, locating drug stores, making appoitment with doctors, and online purchase of drugs by customers It should be designed, and developed, with App, admin panel, api and database The budget is $250, and needed in two weeks
I have a program which needs to be programmed onto a S32k NXP evaluation board. I need someone with great embedded systems experience who can figure out the code and is aware of the board.
I am looking for an embedded expert to improve on a motor control stack . The individual will need to come to Thrissur /Kerala to get access to the physical robot . There is a ROS enabled Robot i am working on .There is going to be a fairly heavy performance tuning component and some serious EE skills will be needed. They will definitely need access
...be developed . We are looking for professional who can develop a home automation solution which works on micro controller and wireless technology. This would be a like embedded systme which apply logic and Idea is to control multiple devices with wireless connection. This solution should also be work on Amazon Alexa. Basic BOM would be.... [login to view URL]
I need an embedded browser application with 9 browser window run in one screen (full screen). The screen is divided into 9 parts. Each browser should be zoom out into 18%. There is no url input in the browser, the url is set in setting window, open when application started, the url is not changeable after started. When 1 window is clicked, the windows
We required a Consultant who can support us in building an Intel Processor-based Embedded Systems. Mandatory: • 2+ Years of C, C++ development experience in Intel Processor based Embedded Systems • Experience with developing/debugging device drivers (PCIe, Ethernet, USB) • Experience with developing Memory Device Drivers and File systems (NAND, NOR
I am friend of a person who is running a start-up in Hyderabad, he wants to find a freelancer for around 1 month to support for his IoT based project. The support needed is from the Client and Server side also, for the same he would like to discuss with the freelancer to go ahead on the same. He will have a discussion before taking any decision and I dont have many details of the project. Whoev...
We are looking for experienced ESP8266 Embedded IOT programmer to work on programming project. Skills required: -nodeMCU - WiFi Config (connecting, setting/saving the SSID, credentials) -Performing HTTP requests, creating an HTTP server -Use the hardware I/O (GPIO, I²C, PWM, etc.) -Integration with Android or React Native. Please DONT respond
Should be able to use pic16 on MPLAB ICD3. Using a STATIC Rate Monotonic cycle Scheduler (RMS). The RMS scheduler is pre-emptive and will thus require you to implement a user stack to store context information. All processes arrive initially at time instant 0. So basically there would be 3 task. Need the codes for all of them, with explanation.
I need some changes to an existing website. just to add youtube player and get url from input. and we will have to make it on my computer (i'm a developer as well but for mobile), so we need to have a voice call and u need to have good english :)
Should have knowledge in Embedded Controller System. I share the Url how we need the inverted Pendulum process to be working for. Url: [login to view URL]
I am currently taking a course on thinkific and have used internet downloader to download videos but currently the livestream video is showing 26 chunks. I just need the video downloaded in one file plus I need to know how to do it in the future.
I need a base board with: 2 x I2C connectors Protected 6 x Electronic brick connectors Protected 12VDC in Ethernet with PoE (module) 2200mAh battery backup - with Li-Ion charger and I2C fuel and gauge 2 x 220VAC 5A standard footprint relay Piezo beeper Internal I2C pins for LCD Reset/test button 2 x bi-colour status leds AdaFruit Feather specification socket to accept any Feather board ...
edit and add feature to small project : patients/old people Fall detection with nodemcu ESP8266,gy521 *gyroscope sensor* with cayenne to do: connected with buzzer/led warning,on/off button and push button for instant help request include location * cayenne feature no need to gps* requirements : circuit *maybe with pcb design* and arduino code file.
I need an app that controls the intensity and tempo of the embedded LED for smartphone cameras. Project must be coded using Visual Studio an Xamarin
Hi, I'm looking for a freelancer who has experience with various technologies including: - Embedded Linux, RTOS, and bare metal (no OS) - AWS IoT - IEEE 802.15.4 radios (foundational protocol of Zigbee and others) - Serial communications (SPI, I2C, UART, RS485, 1-Wire, CAN, Ethernet) - 8-bit resource-restrained microcontrollers - 32-bit
Looking for somebody who can code an autonomous system in leJOS and JAVA on nxt robot. Use of Multithreading. Use of data Bluetooth communication is necessary for giving the orders. Robot should move in xyz.
We require an experienced embedded circuit designer for a project involving building a dual axis solar tracker prototype. The candidate should be able to handle complete design and programming of the circuit and integration with hardware will be in conjunction with a team of engineers.
Project is at concept/demo stage and is a blog that offers video content for health care of o...interactions on a Blogger blog site. Best if you've previously set up GA on a Blogger site and used Tag Manager to create YouTube triggers that fire in response to interactions with embedded YouTube videos. On my site, each video plays on a separate page.