Flash animation amplifier jobs

Tapis

Carian terbaru saya
Tapis melalui:
Bajet
hingga
hingga
hingga
Kemahiran
Bahasa
    Status Pekerjaan
    893 flash animation amplifier tugasan ditemui, harga dalam USD

    Small high efficiency speakers and amplifier for use in embedded projects - Develop complete hardware. I need develop completed hardware, and indicate the supplier in china where i can buy speakers to use with application. I need schematic, pcb, and supplier list.

    $150 (Avg Bid)
    $150 Avg Bida
    9 bida

    I need an active (12v DC power supply), low noise, low frequency (1Hz to 10Hz) receiver/amplifier (3V peak to peak output) with a low pass filter set at 12Hz. I need the design, schematic, and PCB design in Altium. The PCB will need to be 28mm wide. Length and layers are flexible

    $209 (Avg Bid)
    $209 Avg Bida
    20 bida

    ...information on this description. ESP32 TTGO Lora V2.0: ([login to view URL]) Load Cell Amplificator HX711: ([login to view URL]) Temperature Sensor DHT22: ([login to view URL]) 5 and 4 pin connector: [login to view URL] PCB max size: 170x170 mm Deliverables

    $536 (Avg Bid)
    $536 Avg Bida
    20 bida

    ...for an experienced Electronic Engineer that can perform Circuit design. The purpose of the design is to provide a stable gate biasing circuit for a LNA amplifier to properly biasing the amplifier to draw the optimum amount of current (Id = 25mA). Please read the instructions in the LNA data sheet on how to properly bias the LNA. Attached, please

    $123 (Avg Bid)
    $123 Avg Bida
    13 bida

    ...for wireless rf transceiver for analog audio using Silab's EFR32 wireless SOC or similar. This is to be used by us in Multimedia Speakers. The communication would be from amplifier to Woofer. The scope of the work would include developing the hardware (which should be pretty straightforward since this is a Wireless SOC with its own MCU), write the code

    $248 (Avg Bid)
    $248 Avg Bida
    1 bida

    Hello, I need to design a 2.1 soundbar PCB along with DSP programming. I have a reference design of Texas Instruments's value soundbar which have onboard amplifier chips, DSP, EPROM etc. I need some modification on this PCB according to my design requirement.

    $361 (Avg Bid)
    $361 Avg Bida
    12 bida

    ...around the hat band iii. Variant/Option to include a TI CC2590 or CC2592 LNA/Power Amplifier for additional range (BLE/CC2652 2.4 GHz version only) iv. A microswitch push button or two for debug and test (optionally populated for production too) v. Additional Flash memory for keeping a complete lifecycle data history. (2-4M) vi. Possible micro-USB

    $1220 (Avg Bid)
    $1220 Avg Bida
    18 bida

    A printed circuit board layout for an audio amplifier. Take my schematic and my parts list and make a nice printed circuit board layout for me and I pay for the Gerber files(software plans to make the boards). Nothing physical to buy or sell. Just the software plans. Preferably in Eagle CAD format.

    $124 (Avg Bid)
    $124 Avg Bida
    2 bida

    I want you design and make a digital weighing scale that will fit into a model that I have designed. The parts will consist of a strain gauge/ load cell and a load amplifier, wired to a PCB board and LCD screen and a speaker. The scale must be able to be properly and easily programmed. The maximum weight range will be 1Kg. Please note that you must

    $684 (Avg Bid)
    $684 Avg Bida
    13 bida

    I need a circuit designed for a Raspberry Pi that contains t...minutes and a signal should be sent to the Raspberry Pi over either an SPI or I2C interface to shutdown the Raspberry Pi. Within the same circuit, I'd also like to power an AV amplifier/distributor. The circuit should take one RCA input (Video, Left Audio, Right Audio) and have 4 outputs.

    $204 (Avg Bid)
    $204 Avg Bida
    14 bida

    Need a simple PCB for a small amplifier to connect from raspberry PI audio output to Car Speakers.

    $50 (Avg Bid)
    $50 Avg Bida
    31 bida

    Need a simple PCB for a small amplifier to connect from raspberry PI audio output to Car Speakers.

    $34 / hr (Avg Bid)
    $34 / hr Avg Bida
    31 bida

    Hardware electronics including Circuit design for instrumentation amplifier and filters in transistor level as well as chip level. Circuit design will be on the theory and simulation of AD8232

    $30 (Avg Bid)
    $30 Avg Bida
    4 bida

    I need to design and simulate a typical telecommunication receiver system operating in Ku band(14.25 to 14.5 Ghz) consisting of Bandpass filter,Low ,noise amplifier,mixer,IF filter,adc and signal processor..with modulated and unmodulated signals.

    $126 (Avg Bid)
    $126 Avg Bida
    11 bida

    I need to design and simulate a typical telecommunication receiver system operating in Ku band(14.25 to 14.5 Ghz) consisting of Bandpass filter,Low ,noise amplifier,mixer,IF filter,adc and signal processor..with modulated and unmodulated signals.

    $189 (Avg Bid)
    $189 Avg Bida
    8 bida

    ...wilikison divider). I need someone with the ability to design the divider and optimized miters and such. Each RC chip outputs I and Q signals (6 total) with are sent to an amplifier (hence 6 amplifiers circuits). The output of the 6 amplifiers will go into 3 dual ADC's. The ADC will then send signal to connectors will an FPGA card will plug into. There

    $3505 (Avg Bid)
    $3505 Avg Bida
    6 bida

    Dear Mr Mrityunjay G., we read you profile and would like to offer you to design and do a product catalog (print and pdf) about audio amplifier products (based on Adobe indesign). It should be a good implementation itself. We would need serveal languages. Startingpoint would be english. For doing a perfect work we expect for the first shot 32 hours

    $232 (Avg Bid)
    $232 Avg Bida
    1 bida

    Hardware electronics including Circuit design for instrumentation amplifier and filters in transistor level as well as chip level.

    $532 (Avg Bid)
    $532 Avg Bida
    19 bida

    Hardware electronics including Circuit design for instrumentation amplifier and filters in transistor level as well as chip level.

    $502 (Avg Bid)
    $502 Avg Bida
    41 bida

    Design, analysis, and calculation of filter design, RF power amplifier, a matching network (IMN & OMN) using smith chart, antenna matching, power calculation, Free space path loss (FSPL) estimate from Transmitter system to the receiver device, layout considerations, practical components selection and complete circuit design.

    $188 (Avg Bid)
    $188 Avg Bida
    3 bida