
In Progress
Posted
Paid on delivery
Job Title Hardware Engineer Needed: ESP32-S3 Low-Power Audio Recorder PCB (Dual Variant Prototype Layout) Job Description I am looking for an experienced electronics design engineer to create a custom, compact PCB layout based on the ESP32-S3 microcontroller. The target system is a battery-powered, offline audio data-logger intended to record sound locally to a microSD card during specific daily schedules and securely upload files to a remote server over Wi-Fi during a specific time window. To optimize power consumption and sound performance, I require TWO (2) separate PCB layout variations based on the same core schematic template. Scope of Work & Deliverables The freelancer will provide full design files (EasyEDA Pro/KiCad) alongside two separate production packages completely optimized for automated JLCPCB SMT Assembly (including Gerbers, Drill files, BOM, and CPL/Pick-and-Place coordinates). Common Core Specifications (Both Variants) 1. Microcontroller: ESP32-S3-WROOM-1-N16R8 module (16MB Flash, 8MB PSRAM). 2. Antenna Requirement: Must use the module version featuring a [login to view URL] / IPEX external antenna connector (not an integrated PCB trace antenna). 3. Storage: Integrated push-push MicroSD/TF card slot wired via high-speed SPI routing. 4. Power Input: Dual paths: Primary USB-C port (5V input) and secondary breakout header pin inputs for 5V/GND. 5. Battery Path & Connector: Onboard 1.25mm pitch JST-PH vertical connector wired to accept large capacity 3.7V Lithium-Polymer cells (2500mAh to 6600mAh+). 6. Battery Polarity: Must strictly match the Adafruit Standard Polarity (Looking at the male PCB header face with the indexing slot facing UP: LEFT pin is VBAT+ / RIGHT pin is GND). 7. Power Protection & Charging: Integrated USB charging circuit (e.g., TP4056 profile) and full lithium protection circuitry (over-charge, over-discharge/low-voltage cutoff, and over-current protection) with a low-quiescent 3.3V LDO. Microphone Variant Specifications • Variant A (I2S Architecture): Houses exactly ONE (1) TDK InvenSense ICS-43434 digital I2S microphone. • Variant B (for Deep Sleep capability) (Ultra-Low-Power PDM Architecture): Houses exactly ONE (1) Vesper VM3011-U1 digital PDM microphone (JLCPCB Part #C7149370). The VM3011's DOUT pin must route straight to an ESP32-S3 hardware RTC EXT0 GPIO pin (e.g., GPIO 4) to act as a system-wide hardware wakeup trigger from Deep Sleep. The I2C lines must also route to the MCU for threshold settings. The software firmware must be/should be able to be configured to utilize the ESP32-S3's internal hardware PDM-to-PCM conversion matrix to record clean WAV files from the VM3011. Component Optimization Note To minimize factory assembly fees, you must prioritize components from the JLCPCB "Basic Parts" library for standard passives, regulators, and common chips where possible. Anti-Spam Application Filter To prove you have read this brief completely and are not an automated bot, please start your cover letter proposal with the phrase: "RED TO THE LEFT, BLACK TO THE RIGHT." Milestones: • Milestone 1 (50% of budget): Delivery and approval of the complete circuit schematic block and initial 3D rendering layout. • Milestone 2 (50% of budget): Final delivery of the Gerber, BOM, and CPL files checked cleanly against the JLCPCB design rules (DRC). The final deliverable source project files must be provided natively in either EasyEDA Pro or KiCad, utilizing the factory's components database to ensure zero assembly layout mismatches at checkout.
Project ID: 40751813
28 proposals
Remote project
Active 5 days ago
Set your budget and timeframe
Get paid for your work
Outline your proposal
It's free to sign up and bid on jobs
28 freelancers are bidding on average $176 USD for this job

RED TO THE LEFT, BLACK TO THE RIGHT. Hi, I am an embedded systems engineer with over 16 years of experience. I have extensive experience with compact, battery-powered hardware and embedded audio systems, taking products from concept through prototyping and production. I can design both microphone variants in KiCad around a shared core, paying particular attention to sleep current, battery protection, audio routing and your specified battery polarity. Before layout, I would confirm the external-antenna module and exact battery connector, then validate the VM3011 wake path and PDM-to-PCM recording requirements. I will follow your two 50% milestones: the complete schematic and initial 3D layout for approval, followed by native project files and separate Gerber, drill, BOM and CPL packages for each variant. I will prioritize JLCPCB Basic Parts where practical and check footprints, component orientation and factory design rules before delivery. I can also help with firmware bring-up if needed. What board dimensions and mounting constraints should I work to, and do you already have a schematic template? My bid covers both PCB variants and their manufacturing files, with delivery within 14 days after the specifications are confirmed. Please contact me to discuss details.
$250 USD in 14 days
7.7
7.7

Hello, I’m an Embedded Hardware & PCB Design Engineer experienced with ESP32-S3, battery-powered devices, audio hardware, and production-ready PCB design. I can develop both PCB variants from your common schematic, including the ICS-43434 I2S version and the VM3011 PDM low-power version, while keeping the layouts compact and optimized for JLCPCB assembly. I’ll handle the ESP32-S3 RF section, microSD high-speed routing, Li-Po charging/protection, low-quiescent 3.3V power, microphone interfaces, RTC wake-up path, connectors, and complete DFM/DRC checks. I also have experience designing compact ESP32-based trackers and battery-powered 4/6-layer boards, including BOM optimization and JLCPCB/LCSC manufacturing preparation. Deliverables will include the native EasyEDA/KiCad project, two production-ready layouts, Gerbers, drill files, BOM, CPL/PnP, and JLCPCB-compatible component selection. I’m also comfortable working with JLCPCB Basic Parts to reduce assembly cost and avoid checkout mismatches. Best regards, Mahmoud
$140 USD in 7 days
5.6
5.6

RED TO THE LEFT, BLACK TO THE RIGHT. Hi, I’m an experienced Hardware/Electronics Engineer with 7+ years of hands-on experience designing and prototyping embedded hardware and PCBs. I’ve worked on several ESP32-based products and can handle this project from the schematic/layout stage through prototype validation. I can design both PCB variants around the ESP32-S3-WROOM-1-N16R8, including the I2S and ultra-low-power PDM microphone versions, power/charging/protection circuitry, microSD, USB-C, JST battery input, external antenna, RTC wake-up routing, and optimized placement/routing for low-power and audio performance. I can also prepare the complete EasyEDA Pro/KiCad source files and JLCPCB-ready Gerber, BOM and CPL packages using suitable factory components. What I particularly offer is prototype support: I can help you place the order with JLCPCB, review the assembly before production, and perform functional testing/debugging on the finished prototype if required. I can also perform additional schematic/design checks, although that would require additional engineering time. I’ve built several ESP32-based products and can share videos of my previous work. You’re also welcome to visit my profile and see the reviews from previous clients and projects. I can start from your existing specification and take the design through to a tested prototype.
$250 USD in 7 days
4.7
4.7

As a team of skilled and highly-proficient Electrical Engineers, we possess the comprehensive skill set necessary to realize your vision for the ESP32-S3 Prototype PCB Layout Design project. Our expertise in Arduino, Circuit Design, Electronics, Embedded Systems, Microcontroller, and PCB Layout aligns seamlessly with your requirements. We have extensive experience in developing low-power systems and have worked on numerous battery-operated projects like yours that required high efficiency and reliable performance. Drawing from our in-depth understanding of electronics design and our mastery with tools such as KiCad, Proteus, and Altium Designer, we can confidently assure you a meticulously designed ESP32-S3 prototype PCB that's perfectly optimized for automated assembly. Over the course of the project, we will provide not just quality work but consistent and effective communication, ensuring your needs are met at every stage. Moreover, our commitment to refining complex RF challenges into efficient real-world solutions makes us well-suited for this project. We offer more than just technical expertise; we provide support throughout the entire development cycle -- from concept to hardware implementation. Choose us and be assured of great results that will exceed your expectations. Together, let's make this ESP32-S3 prototype a reality so you can record the crisp audio data you need with utmost ease!
$250 USD in 7 days
2.5
2.5

Developed industrial automation with motorized positioning and feedback, including fixture design and data exchange with a PC. For your ESP32-S3 prototype: I will optimize the layout for JLCPCB Basic Parts, ensure correct routing of I2S/PDM microphones and the Li-Po battery power circuit with protection. How do you plan to verify the VM3011 wakeup via EXT0 GPIO?
$140 USD in 14 days
1.3
1.3

RED TO THE LEFT, BLACK TO THE RIGHT. I am a hardware design engineer specializing in ESP32 systems, low-power IoT, and audio PCB layouts (KiCad/EasyEDA Pro). I can deliver production-ready manufacturing packages for both variants optimized for JLCPCB SMT assembly. Feel free to look at some of the custom boards I designed in the portfolio section https://www.freelancer.com/u/HeyAbhinav?sb=t Engineering Execution Strategy: • Variant A (ICS-43434): Clean I2S routing with length-matched clock/data lines to prevent audio jitter. • Variant B (VM3011-U1): Precise routing of the Zero-Power Sensing DOUT pin directly to RTC GPIO 4 for hardware deep-sleep wakeup, plus routed I2C lines for threshold configuration. • Power & Protection: TP4056 charge management with Adafruit-polarity JST-PH pinout, DW01A/FS8205A Li-Po protection circuit, low-quiescent 3.3V LDO, and USB-C/breakout power paths. • JLCPCB Optimization: Maximize JLCPCB "Basic Parts" for passives/LDOs to minimize setup fees. Deliverables: Schematic & PCB layout files, Gerber RS-274X, NC Drill, LCSC-matched BOM, and CPL Pick-and-Place coordinates. Ready to start immediately.
$250 USD in 7 days
0.0
0.0

RED TO THE LEFT, BLACK TO THE RIGHT. Hi — we're VoltEdge Studio, an electronics engineering studio. Your "ESP32-S3 Prototype PCB Layout Design" is exactly our core work: dual-variant ESP32-S3 low-power audio recorder PCB — Variant A with ICS-43434 I2S mic and Variant B with VM3011 PDM mic routed for RTC EXT0 deep-sleep wakeup, USB-C + JST-PH battery path with TP4056 charging and full LiPo protection, microSD over high-speed SPI, all optimized for JLCPCB SMT assembly with Basic Parts. You'd get: native KiCad schematic + layout (ERC/DRC clean), Gerbers + drill + CPL ready for JLCPCB/PCBWay, BOM with part numbers, and a short design-review note. Timeline: 7 days to first review issue. Fixed price $150 USD (within your posted $30–$250 range). We work async via messages and answer in writing within 24h — no calls needed. — VoltEdge Studio
$150 USD in 7 days
0.0
0.0

RED TO THE LEFT, BLACK TO THE RIGHT. Creating a compact PCB layout for a low-power audio recorder is no small task. If the design isn’t optimized, you risk inefficient power use and poor sound quality. This can derail the entire project and lead to delays. I’d approach this by focusing on the specifics you’ve outlined. I can create two distinct layout variations that meet your needs for power efficiency and audio performance. By using the JLCPCB "Basic Parts" library, I’ll keep costs down while ensuring the design is robust. I’ll also ensure that the charging circuit and battery protection meet the required standards. I understand the importance of revisions, so I’ll be ready to adjust until you're completely satisfied. What’s your timeline for this project? Do you have any existing assets or designs to work from?
$100 USD in 7 days
0.2
0.2

Hi, I’m a hardware and embedded engineer based in Barcelona. I’m currently working on a battery-powered project involving USB-C charging, power management, schematic design, and PCB layout. I work with KiCad and can develop both PCB variants and provide the editable source files, 3D views, Gerbers, drill files, BOM, and CPL files for JLCPCB assembly. My scope would cover hardware design and manufacturing files, with prototype assembly and physical testing handled by your team. Could you confirm whether firmware development is also expected, or only hardware support for the described functions?
$250 USD in 12 days
0.0
0.0

Iași, Romania
Payment method verified
Member since Oct 5, 2026
$250-750 USD
$30-250 USD
₹600-1500 INR
₹12500-37500 INR
₹1500-12500 INR
$8-15 USD / hour
₹600-1500 INR
$30-250 USD
$2-8 USD / hour
$8-15 USD / hour
₹12500-37500 INR
$15 USD / hour
$250-750 USD
$10-1000 USD
£20-250 GBP
€30-250 EUR
$10-30 USD
$250-750 USD
₹1500-12500 INR
₹12500-37500 INR