custom Arduino mega 2560 PCB

Dibatalkan Disiarkan 6 tahun lepas Dibayar semasa penghantaran
Dibatalkan Dibayar semasa penghantaran

Move a working developed Adruino Mega project to standalone ATmega module.

1 additional integrated circuit + custom Header / Connectors for external sensors/modules,

Could also be done Via custom Expansion Shield + Mega2560-core Mini 2560 for example.

Custom Expansion Shield specs needed / ATmega module

Additional circuit :

max31856 EGT

1 x 2 pin plug

or

5 Pin header plug for existing prebuilt module

1 x 2 pin power

9v ..14v vehicle power

Fused, reverse pol protected, 5v 2A

1 x 3 Pin

Serial Comms output

1 x 5 pin plug

Rotary encoder/switch

4 x 3 pin plugs

5v Pressure sensors input

4 x 3 pin plugs

Temp sensors

DS18B20 based sensors network so will have 4.7K resistor signal-5v on board on single anolg input

1 x 3 pin plug

AFR

ground, 5v, analog input signal

1 x 4 pin header

on board Knock sensor module (5cm x 5cm)

ground, 5v, analog input signal, digital input signal

1 x 2 pin plug

External knock sensor input to module

1x 3 pin

Ethanol sensor

Ground, 5v, Digital input

1 x 8 pin plug

Trans module plug

ground, 5v, 6x digital inputs

2 x 3 pin

analog future expansion

ground, 5v, analog input signal

1 x 6 pin plug

external relay module

5v, ground, 4 x digital outs

1 x 5 pin on board Header

HC-05 bluetooth Module

Note:-

headers/modules to centre of board

plugs to side and rear - stacked for easy side access via custom enclosure

After re-avaulating we feel the best route is a custom sheild design which will use
1. Mini mega 2560 plug in module
http://www.inhaos.com/product_info.php?products_id=118

2. 36v-12v Power supply module
http://www.inhaos.com/product_info.php?products_id=145

3. HC-05 Bluetooth module

4. MAX6675 Thermocouple Module

5. Our our custom Knock sensor module 5 pin

6. Stacked header connectors for external sensors, switches, comms, expansion.

We are using modules as this will cust down on complicated incircuit designs and time, and will allow easy replacement or upgrade in future.

Pengaturcaraan C Kejuruteraan Elektrik Susun Atur PCB

ID Projek: #14882369

Tentang projek

29 cadangan Projek jarak jauh Aktif 6 tahun lepas

29 pekerja bebas membida secara purata $287 untuk pekerjaan ini

highfliercnr

Dear Sir, If you are looking for an highly skilled hardware engineer, I believe that I am the one who you're looking for. I am also an experienced PCB designer who has over 16 years design experience on complex PCB Lagi

$500 USD dalam 5 hari
(111 Ulasan)
8.5
sagradoamicus

Hi Sir I am an expert PCB designer with more than 8 years of experience I can do it for you. Please have a look at my profile I assure you quality work and on time delivery Relevant Skills and Experience Please review Lagi

$600 USD dalam 8 hari
(255 Ulasan)
8.0
liveexperts123

Hi i can do this perfectly ......................................................................................................................

$833 USD dalam 3 hari
(53 Ulasan)
7.2
binyameen441

i am an electrical engineer. i am expert in pcb design Relevant Skills and Experience electrical engineer Proposed Milestones $55 USD - pcb

$55 USD dalam 3 hari
(120 Ulasan)
6.6
pcbdcs

Have to develop the PCB. Relevant Skills and Experience 10+ years Proposed Milestones $90 USD - PCB Design

$90 USD dalam 3 hari
(121 Ulasan)
6.7
ahmad5857

We are professional engineers and developers skilled in pcb designs, we do our jobs in Altium and Eagle. Please visit our portfolio and see how best we are in designing PCB layouts. Lets discuss !! Relevant Skills a Lagi

$350 USD dalam 3 hari
(37 Ulasan)
6.9
Davelelievre

The current price and timescales are only place holders to allow me to communicate with you If you think I can help then please send me further details Best Regards Dave Lelievre Poole Dorset Relevant Skills and Exper Lagi

$555 USD dalam 10 hari
(27 Ulasan)
6.2
hamasaki

I'm bidding on this project to make a bespoke ATMEGA2560-based PCB with additional components/relays/etc on it. The bid is for schematic + pcb layout made in Altium Designer. Relevant Skills and Experience Schemati Lagi

$850 USD dalam 3 hari
(6 Ulasan)
5.6
gustavodaboin

Hello, it is a pleasure to greet you, I like carry out the project if you allow me and tell me all the details ... Habilidades y experiencia relevante Very much Htos propuestos $100 USD - to start project $122 USD - Lagi

$222 USD dalam 10 hari
(28 Ulasan)
5.2
prefectworld

Programming has developed as an energy of mine; I get pleasure from working in numerous fields of this profession. Relevant Skills and Experience PCB layout, c programming Proposed Milestones $30 USD - initial miles Lagi

$30 USD dalam 2 hari
(22 Ulasan)
5.1
gauravsharma132

Design board around Mega 2560 Relevant Skills and Experience We have worked around arduino for long time, literally since its inception. We can help you design the board. Proposed Milestones $688 USD - As per discuss Lagi

$688 USD dalam 7 hari
(16 Ulasan)
5.3
saminatinny

A proposal has not yet been provided

$242 USD dalam 7 hari
(5 Ulasan)
4.0
bogdan2451629

Hello do you need ready soldered board or PCB design? I coud all. Relevant Skills and Experience 5 years hardware design, develop expirience Proposed Milestones $155 USD - pcb design, gerber files

$155 USD dalam 3 hari
(7 Ulasan)
4.0
gab3iel

hi, I have designed multiple devices from Arduino design files. Eagle would be the way to go unless you already started using a different CAD tool. Has the new board got to have the Arduino mega footprint or can it be Lagi

$249 USD dalam 7 hari
(3 Ulasan)
4.0
sidou82

Hi Sir, I would like to work on the custom arduino module, we can discuss more detais by chat if you agree. Please take a look to my profile to get an idea about my skills and backgrounds. Thank you.

$100 USD dalam 3 hari
(10 Ulasan)
3.9
rishiajmera

Hello, Greetings! With a proven track record of successful achievements, I am pleased to present my application for your consideration as a Freelancer. Relevant Skills and Experience Please have a look at my profile a Lagi

$155 USD dalam 3 hari
(8 Ulasan)
3.7
nextrotek

We are 10 Members team with 8+ years of experience. Specialized in all sorts of Electrical and Electronics Automation. We design and Build Products in most efficient possible manner Our Services: * LabVIEW an Lagi

$222 USD dalam 3 hari
(1 Ulasan)
3.4
chyconsl

Hi, I have gone through the project thoroughly and understood your project requirements. With years of experience and dedicated efforts, I will be glad to offer an outstanding services; Relevant Skills and Experience Lagi

$211 USD dalam 3 hari
(1 Ulasan)
2.7
isparrowsolution

Hello hiring manager I read your details and I understand is that you wish to move Adruino Mega project to standalone ATmega module. Relevant Skills and Experience We are expert in C Programming, C# Programming C++ P Lagi

$250 USD dalam 3 hari
(3 Ulasan)
2.1
ingcoenergie

Hi, I am interested to work on this project. Please let me know the detail

$231 USD dalam 18 hari
(0 Ulasan)
0.0