Sedang Disiapkan

RGB LED driver controller

I have a 10w RGB LED package (3w per colour) and need to drive it so we can select:

Just red

Just green

Just blue

White (all three together)

Yellow (red & green together)

Each of the LED's requires different voltages, and current limited to 350mA per channel.

I tried previously to do this, but with little success and just destroyed the LED's.

To limit the current I tried adding NSI50350ADT4G's, but they get VERY hot so dont think this is a usable solution. Also, as they get hot, the current goes down so not a great idea.

The LED's are common anode

Here's a link for the LED

https://www.amazon.co.uk/gp/product/B01DBZK64K/ref=ox_sc_act_title_2?smid=A29VZUSG1WM39I&psc=1

I've uploaded an image of the original Chinese flood light controller, but dont want to use the IR remote. Must be via a single N/O switch.

I want to control the colour by pressing a N/O switch. Each time it's pressed, it changes to the next colour.

Once tested on an arduino, I plan to build it on a ATMEGA328-AU chip.

There are lots of circuit ideas out there about how to manage voltage and current for these LED's, but no guess work please. If you dont have the skill and knowledge, dont bid.

This is a re-posted project as it was given to a freelancer without the appropriate electronics knowledge to complete it properly.

Kemahiran: Arduino, Reka Bentuk Litar, Kejuruteraan Elektrik, Elektronik, Mikropengawal

Lihat lagi: rgb led controller, high power rgb led driver, rgb led driver circuit, rgb led driver ic, rgb led driver i2c, rgb led driver arduino, rgb led driver ic pwm, rgb led driver circuit diagram, led strobe controller, english chinese part time translator malaysia, translation job english chinese part time, 120 volt led driver, led matrix controller, mikrokontroler rgb led projects schematic, rgb led wireless controller, 128x64 led driver controller, atmega rgb led driver, pic rgb led controller, rgb led bluetooth controller, rgb led controller 89c2051 asm

Tentang Majikan:
( 41 ulasan ) Offord Darcy, United Kingdom

ID Projek: #17155631

Dianugerahkan kepada:

anhvu100

Hello, First of all, selecting NSI50350ADT4G is a wrong decision as it is a linear converter. That means any unused energy is consumed on this IC and produces a lot of heat. When the temperature reach the thermal sh Lagi

$250 USD dalam 7 hari
(23 Ulasan)
0.0

27 pekerja bebas membida secara purata $162 untuk pekerjaan ini

MElizabethp

Hello my name is Maria I am an electronic engineer, I would love to design this circuit for you, I have plenty of experience working with electronic and electric designs (squematic and PCB layouts), programming microco Lagi

$250 USD dalam 3 hari
(5 Ulasan)
4.5
sourabh470

Hello Sir, its an easy task for me. I have 4 years experience in PCB designing in EAGLE (single multilayer and flex) As NSI50350ADT4G has very high PD value 11W without a good heat sink it won't work properly. 2 Lagi

$150 USD dalam 6 hari
(12 Ulasan)
3.9
FarzanSaleem

I have 3+ years of experience in Hardware designing, firmware development and complete Product Development. I will provide you complete hardware consultancy and also i will provide schematics and BOM of circuit. If y Lagi

$150 USD dalam 3 hari
(7 Ulasan)
4.1
Kristsp

Hi, I am interested to work with your project. To be sure that it works as expected, I would need to source the very same leds you have. For project delivery, do you need complete prototype PCB or just a schematic? Sen Lagi

$200 USD dalam 14 hari
(2 Ulasan)
3.2
jawwadHusNain

hi, I go through your requirements, and found that i can do your project. i have experience in communication protocols and controller also. you may go through my portfolio and projects. thank you

$170 USD dalam 10 hari
(4 Ulasan)
3.1
Omaresl

Hello I'm an engineer in electronics and I can help you with your project Actually I have good experience with Opto electronics. The solution that I can gave you is a Power circuit with a microcontroller that Lagi

$90 USD dalam 5 hari
(5 Ulasan)
2.3
$200 USD dalam 10 hari
(2 Ulasan)
2.4
anmol2701

Hi, Thanks for sharing the project requirements I am an adept arduino programmer and would like to work on this project Welcome to have an interview session for the project understanding Regards NG Services

$333 USD dalam 7 hari
(2 Ulasan)
1.4
$116 USD dalam 5 hari
(2 Ulasan)
1.3
AhmedSobhiSaleh

Hi, I am a professional electrical engineer. I am an expert in designing and simulating circuits and writing arduino codes I also have the hardware to test and confirm working code. You can see some of my work in my po Lagi

$138 USD dalam 5 hari
(19 Ulasan)
0.8
soltracker

How r u?Buddy,,,Its me Imad, Have done 200+ projects regarding matlab, arduino, vb.net, html, php, pcb designing and raspberry pie. U will feel brotherhood..............................

$60 USD dalam 3 hari
(15 Ulasan)
0.6
champsoban

hello there, I am electrical engineer with specialization in electronics engineering. I have been working on arduino microcontroller for 2 years now. I can do this project for you but I will take my time to complete it Lagi

$111 USD dalam 7 hari
(1 Ulasan)
0.8
emirhodzic3

Dear, I'm mechanical engineer with good electronics and arduino skills.

$88 USD dalam 7 hari
(0 Ulasan)
0.0
Paradoxx84

Hello. I'm an electronic engineer / MCU programmer, the task is not very complicated, it will be MCU and some proper mosfet keys with current sensing..I have my own arduino or stm 8 or stm 32 (what CPU you like more?) Lagi

$55 USD dalam 5 hari
(0 Ulasan)
0.0
sky19130

Hi, dear! I saw your project. I am a interested in your current driver project. I can do it and i wold like to discuss the details. I will best. Thank you.

$177 USD dalam 3 hari
(35 Ulasan)
0.0
$122 USD dalam 9 hari
(0 Ulasan)
0.0
bijan01in

Hi i am interested to your project. I am familiar with electronics, PIC microcontroller as well as pcb design by eagle. Thanks.

$250 USD dalam 10 hari
(71 Ulasan)
0.0
mcanerbasol

I've been working on power electronics, LED drivers for 2 years. The circuits I built are the ones that conform to the standards (EN-55015, EN-61000). I do not tell you that the system will be in compliance with the st Lagi

$333 USD dalam 15 hari
(0 Ulasan)
0.0
manufcm

I think that it can be solved using resistors, looking the item characteristics, you can use same resistor for all the colors

$166 USD dalam 2 hari
(0 Ulasan)
0.0
Johnwassef

I used microcontrollers alot of times and I am electrical engineer and I enjoy my time doing this stuff.

$155 USD dalam 7 hari
(0 Ulasan)
0.0