Ditutup

mikroC or mikroBasic code programming needed for PIC Microcontroller -- 2

(Do NOT bid for the project if you are not able to send sample of below code)

I need a working code to be written into PIC Microcontroller family where a crystal of 12MHz is being used.

It is a device that will detect object using IR sensor (RX and TX) with 4 indicator LEDs.

The device has an USB plug where data will be sent to and received from PC.

You may use USB HID Terminal from mikroC/mikroBasic for testing which will send command to the PIC so it will generate some function.

LED startup signal: LED1 on, wait 1 sec, LED2 on, wait 1 sec, LED3 on, wait 1 sec, LED4 on

LED standby signal: 0.5 sec Flip Flop of LED1+LED3 and LED2+LED4. (LED1+LED3 on, LED1+LED3 off, LED2+LED4 on, LED2+LED4 off, etc.)

LED active signal: 0.5 sec blinking of LED1+LED2+LED3+LED4 (LED1+LED2+LED3+LED4 on, LED1+LED2+LED3+LED4 off, LED1+LED2+LED3+LED4 on, etc.)

LED hold signal: LED1+LED2+LED3+LED4 on (persistently).

This is what it shall do when the device is plugged into PC (initial action without send/receive data from/to PC):

1. PC shall detect the device/hardware once plugged in. It shall display device name (e.g. "PIC Object Sensor").

2. It shall start the "LED startup signal".

3. Then it shall start IR sensor detection. (When there is no object, "LED hold signal" is activated. And when there is an object, "LED standby signal" is activated)

Function for receiving/sending data from/to PC through USB :

1. If it receive code (e.g. !0001A), activate "LED standby signal". No data to be send to PC.

2. If it receive code (e.g. !0002A), activate "LED hold signal". No data to be send to PC.

3. If it receive code (e.g. !0003A), activate "LED active signal". No data to be send to PC.

4. If it receive code (e.g. !0088A), activate "LED hold signal" and start IR sensor detection for unlimited time. (When there is no object, "LED hold signal" is activated. And when there is an object, "LED standby signal" is

activated). No data to be send to PC.

5. If it receive code (e.g. !00AAA), activate "LED standby signal" and start IR sensor detection for unlimited time. (When there is no object, "LED standby signal" is activated and send data to PC (e.g. 1B2F1022BBA1FF). And when there is an object, "LED active signal" is activated and send data to PC (e.g. 2B3F003D1FFAA0)).

Basically it is a simple code if you know what you are doing.

I am using PIC Microcontroller (microchip) only, thus do NOT offer me code in ATmega, PLC, Arduino, Raspberry Pi, etc.

I have a tight budget of 25 EUR only.

To prove that you able to do it, please send me the code in mikroC/mikroBasic or the hex code when I contact you through chat for above working sample function. I will let you know the PIC number if I think that you might be the right candidate.

So, don't simple bid for the project if you are not able to show me above sample.

I will give a full detail of the project which contains approximately 8 similar functions.

I will award this project to you only after I check your sample code and it's working.

The full code (mikroC/mikroBasic and including hex code) shall be submitted upon real project completion.

Kemahiran: Elektronik, Mikropengawal, Arduino, Pengaturcaraan C, Kejuruteraan Elektrik

Lihat lagi: pic microcontroller visual programming, pic microcontroller gps mikroc, visual studio pic microcontroller programming embedded software, gps nmea mikroc code pic microcontroller, code pwm pic microcontroller, graphical lcd interfacing pic microcontroller code, pic microcontroller programming jobs, project pic microcontroller 16f628source code, code pic microcontroller, programming code electronic weighing machine microcontroller, clock display pic microcontroller code, voltmeter ammeter pic microcontroller code, pic microcontroller usb midi code, code pic microcontroller usb, pic microcontroller led project assembly code, pic microcontroller rapid fire code, pic microcontroller source code assembly, programming the pic microcontroller with mbasic embedded technology

Tentang Majikan:
( 0 ulasan ) Tangerang, Indonesia

ID Projek: #27498528

4 freelancers are bidding on average €22 for this job

(32 Ulasan)
5.5
Adeel2k14

Hope you are fine. I have understood the project description, i am 100% sure i can complete your task. I have experience in solving various electrical problems. Moreover i have the expertise in the following mentione Lagi

€20 EUR dalam 2 hari
(3 Ulasan)
3.1
aneeba231

I have experience in C programming with I2C and SPI interface and have good command on Microchip and AVR with expertise in MPLAB, MickroC and proteus.

€30 EUR dalam 7 hari
(0 Ulasan)
0.0
profhosam01000

I CAN MAKE THIS PROJECT IN A VERY FIXED TIME AND PRICE YOU CAN TAKE A LOOK IN MY PROFILE TO SEE WHAT I COULD DO IF YOU INTERESTING

€19 EUR dalam 5 hari
(0 Ulasan)
0.0