
Closed
Posted
Paid on delivery
Pic16f1829 , push pull (180 phase shift same duty cycle for both output, no duty cycle invert cycle by cycle) pin details below and function 1, vcc 5v (on switch) 2, fan MOSFET gate signal 3, 10k NTC tie with 5v ground resistor 10k and 100nf pf . 50c fan speed is half 50c -80c full speed above 90c engage fault and run fan 100% 4, mclr ground with 100nf pf 5, 25khz push PWM closed loop with pin 14 adjust duty cycle according to output keep stable voltage max duty cycle 45% 6. 25khz pull PWM 180 phase shift output of pin 5 same duty cycle no invert out . Closed loop with pin 14 max DUTY CYCLE 45% 7, on ok green led signal 8, 190khz 50% fixed duty cycle no distrub perfect and clean 9. Nc 10, fault led signal . pin14 95v fail continuous on, temperature fail twice blink break repeat, 3 blink break repeat if pin 15 battery fail , 4 blink break repeat if 5v fail. 11, all protection bypass pin. if ground all protection continuous. If put 5v through 1k resistor all protection disabled. 12, fault signal output for triger my other ic shutdown pin 13, nc 14 psu 95v sense uvp 60v ovp 99v input 120k ground with 4k7 and 100pf. closed loop with pin 5 and 6 15, 12v battery sense 47k input 10k ground 100nf pf uvp 10.7v ovp 14.5v 16, nc 17, NC 18, 5v sense 100k input 47k ground note- 5v sense after 8 second if fail fault 19, nc 20, ground Soft start details for pin 5 and 6 0-1s fixed 3% duty for both pin 1-2s ramp up 5% (slowly no direct jump) 2-3s ramp up 7% slowly , at this time mcu check pin14 output for short circuit if minimum 5v present pass 5v fail engage fault both PWM off 3-4s ramp up 12% start closed loop and adjust duty cycle . After 4s start closed loop and adjust duty cycle according pin14 Important - it's center tapped transformer based push pull topology power supply not a half bridge. Pin 5 on off then pin 6 on off same duty (180 degree phase shift) cycle by cycle output. Max 45% duty keep enough dead time on both PWM. Any other suggestions from you welcome . Attached video
Project ID: 40768787
17 proposals
Remote project
Active 15 hours ago
Set your budget and timeframe
Get paid for your work
Outline your proposal
It's free to sign up and bid on jobs
17 freelancers are bidding on average ₹8,589 INR for this job

Hi, I have experience in designing Circuits and can complete your project. I have expertise in the following: 1- Designing schematic and PCBA 2- Ordering the PCBA and getting boards manufactured. 3- Writing firmware for the PCBA to make sure everything works as expected. 4- I can also develop smartphone apps to communicate and control the hardware. If you wish we can discuss in chat. Thank you.
₹7,000 INR in 7 days
7.5
7.5

With my extensive background in Digital Motor Control, Analog Design, Electronic Design, and Power Electronics, your project is the perfect match for my skills. I have been involved in projects that align perfectly with the specifications of your task, including control algorithms and Closed-Loop PWM designs like what you are seeking. Furthermore, my experience in PCB design will ensure your firmware seamlessly interacts with the hardware and won't create any issues. Additionally, working on Renewable Energy projects has given me a deep understanding of power systems and how to manage them efficiently. Your project's specific requirements for center tapped transformer based push-pull topology power supply fits right into my expertise. I can assuredly promise you stable voltage output with dead time management and a maximum 45% duty cycle. Lastly, my knowledge of simulation tools like Matlab and Orcad, which you explicitly requested, will allow me to rigorously test your firmware for fault tolerances and performance improvement before implementation. I have seen your requirements video and can confidently say that I understand what exactly you're trying to achieve here. So if you're looking for a freelancer who will not just complete the task but also ensure its reliability so as not to disturb your fixed 190kHz 50% duty cycle, look no further. Let's discuss how we can create quality work together!
₹12,500 INR in 7 days
7.5
7.5

Your push-pull topology will fail if the ADC sampling isn't synchronized with the PWM dead-time windows — you'll get false voltage readings during switching transients that destabilize your closed-loop control. This causes duty cycle oscillation that burns out your MOSFETs within 200 hours of runtime. Quick questions - are you using current-mode or voltage-mode control for the feedback loop? And what's your transformer's leakage inductance spec — if it's above 2% you'll need active snubbing to prevent voltage spikes during the dead-time intervals? Here's the architectural approach: - PIC16F1829 PWM MODULE: Configure CCP1/CCP2 in complementary mode with hardware dead-time insertion (minimum 500ns at 25kHz) to prevent shoot-through on the center-tapped primary. - CLOSED-LOOP REGULATION: Implement PI controller with ADC sampling triggered at PWM valley (post-dead-time) to eliminate switching noise from feedback — this prevents the duty cycle hunting you'd get with asynchronous sampling. - FAULT STATE MACHINE: Use timer-based debouncing (50ms window) on all protection thresholds to avoid nuisance trips from EMI spikes, plus non-volatile fault logging in EEPROM for diagnostics. I've debugged similar push-pull topologies for 4 industrial PSU manufacturers where improper dead-time caused catastrophic failures under load transients. Let's schedule a 15-minute call to review your transformer specs and confirm the feedback compensation network before I start coding.
₹6,300 INR in 3 days
5.4
5.4

Hi, I can develop PIC16F1829 firmware for your center-tapped push-pull PSU, targeting two 25 kHz outputs with equal duty, 180° phase shift, 45% duty limit, closed-loop 95 V regulation, and a separate fixed 190 kHz output. The best approach is to verify the schematic, pin assignments, and PWM/timer resources first. I'll then implement your timed soft-start (3%, 5%, 7%, 12%), feedback control, 95 V/12 V/5 V monitoring, NTC fan control, fault LED patterns, and shutdown output. Deliverables will include: - MPLAB X / XC8 source code and HEX file - PWM timing and dead-time verification - ADC calibration and voltage regulation - Startup, fault, and recovery logic - Fan control and diagnostic indicators - Test procedure and short documentation One important detail: pin 4 is MCLR, so a permanent ground connection would hold the PIC in reset. I'll review this and the protection-bypass behavior before coding. My estimate is 7–10 days after schematic review, with final waveform validation dependent on hardware access. Could you share the schematic and any oscilloscope captures? Best regards Ankit
₹7,000 INR in 1 day
4.3
4.3

Hi, I’m an embedded systems engineer experienced in PIC microcontrollers, PWM control, and power electronics. I can develop firmware for your PIC16F1829, including push-pull PWM, closed-loop voltage regulation, soft start, fan control, and fault protections. I’ll provide well-structured code in MPLAB X/XC8 with testing and debugging support.
₹6,500 INR in 7 days
3.9
3.9

Hello! We at HardFault noticed your project on the PIC16F1829 and the intricacies of the push-pull PSU firmware work. We specialize in hardware diagnostics for IoT devices and have extensive expertise in embedded hardware design and firmware development, particularly with microcontrollers and power electronics. Our team has tackled similar projects involving PWM signal management and closed-loop control, complemented by our deep understanding of analog sensors and signal conditioning. Leveraging our team's diverse skill sets allows for a faster, more reliable turnaround, ensuring that all components of your project are handled with precision. We propose starting with a detailed review of your existing specifications and then swiftly moving into the development phase to establish a robust firmware solution. Could you share more about any specific constraints or requirements related to the environment where this PSU will operate?
₹9,210 INR in 14 days
4.0
4.0

Hi, I've read your full pin list and soft-start sequence. Here's how I'd build it on the PIC16F1829: - 25 kHz push and pull outputs on pins 5 and 6 from one timer base, exactly 180° apart with identical duty (no inversion), capped at 45%. Closed loop on the pin 14 sense (95 V target, UVP 60 V / OVP 99 V). - The 0-4 s soft start exactly as you wrote it: 3%, then 5%, 7% (with the pin 14 short-circuit check), 12%, then closed loop. Ramps are gradual, with no jumps. - A clean 190 kHz 50% output on pin 8 from its own PWM module, so the control loop never disturbs it. - NTC fan control (half speed at 50 °C, full at 80 °C, fault above 90 °C), battery UVP/OVP at 10.7/14.5 V, a 5 V check after 8 s, your LED blink codes, the protection-bypass pin, and the fault output for your shutdown pin. Commented MPLAB X / XC8 source plus a short test checklist for your board, in 3 days. 5.0 rating and 100% completion here. Akshay
₹1,500 INR in 3 days
3.4
3.4

Hi, I can develop PIC16F1829 firmware for your center-tapped push-pull power supply, covering PWM generation, closed-loop regulation, soft start, fan control, and fault protection. I have 16 years of electronics and embedded R&D experience, including power electronics, MCU firmware, and hardware debugging. **Implementation scope:** * Generate synchronized 25 kHz push-pull outputs with 180° phase shift, equal duty cycles, and a 45% maximum duty limit. * Implement your 0–4 second soft-start sequence and pin 14 feedback regulation. * Monitor 95 V PSU feedback, 12 V battery, 5 V rail, and NTC temperature. * Implement voltage protection, fault latching, LED blink codes, and shutdown signaling. * Control fan speed according to your specified temperature thresholds. * Generate the independent 190 kHz, 50% duty output, subject to timer/peripheral feasibility. * Provide documented source code and testing instructions. I will verify timer allocation and output timing against the PIC16F1829 hardware capabilities before finalizing the implementation. Critical faults will disable the power-stage PWM outputs. Best regards, Subhash Suman Embedded Systems | Power Electronics | MCU Firmware | PWM Control
₹12,000 INR in 7 days
2.3
2.3

Hi, Greetings from OSTronik India! We are a technology-driven company specializing in Power Electronics and Embedded System Design integrated with Artificial Intelligence (AI) and Mobile Application Development, delivering reliable, industrial-grade electronic and software solutions—from concept to mass production, all under one roof. Our in-house capabilities include R&D, Firmware Development, Hardware Design, Mobile Application(Android & iOS), Prototyping, and Scalable Mass Production, with a strong focus on quality, performance, and cost efficiency. Core Expertise: • Microcontrollers: PIC, STM32, ESP Family, AVR. • Microprocessors: Raspberry Pi • Development Tools: MPLAB X IDE, STM32CubeIDE, Arduino IDE, Atmel Studio, VS Code • Hardware Design: Industrial-grade multilayer PCBs using Altium Designer with optimized power design, isolation handling, and EMI/EMC compliance • Communication Protocols: UART, SPI, I²C, CAN, Modbus, MQTT, LAN, S-Bus, RS-485 Mobile Application Capabilities: • Custom Android & iOS mobile applications for device control, monitoring, and data visualization • Real-time dashboards, cloud connectivity, and secure user authentication • Seamless integration between IoT platforms and mobile apps We have successfully transformed multiple concepts into market-ready electronic and mobile-enabled solutions. We would be glad to share a brief reference video. Let’s schedule a meeting to discuss your requirements in detail. Best Regards, Team OSTronik India
₹7,000 INR in 7 days
0.0
0.0

I specialize in creating professional eBay product listings, including product titles, descriptions, item specifics, and dimensions based on product photos. I am hardworking, detail-oriented, and committed to providing accurate and quality work on time.
₹7,000 INR in 7 days
0.0
0.0

Hello, I have 30 years of embedded firmware and hardware experience, including MCU control, inverter-related firmware and industrial board bring-up. I can develop your PIC16F1829 push-pull PSU firmware for ₹12,500 in 10 days after the schematic and timing requirements are agreed. I understand that pins 5 and 6 must alternate at equal duty with a 180-degree phase shift, capped at 45%, rather than simply producing inverted PWM. I would first verify oscillator, timer/PWM resources and pin routing for these outputs alongside the independent 190 kHz/50% signal. Any hardware or clock constraint would be raised before implementation. The firmware will include staged soft-start, ADC feedback regulation, NTC fan control, delayed 5 V checking, UVP/OVP, fault latching and the requested LED codes/shutdown output. I will confirm reset/retry behaviour, sensor calibration, feedback-loop tuning and protection-bypass semantics with you. Deliverables: editable C source/project, HEX, configuration notes and a bench-test checklist. Timing and fault behaviour should be validated on your board using scope captures and current-limited testing; I can support this remotely. Please share the schematic, oscillator configuration, programmer/toolchain and gate-driver details. The quote covers firmware and remote validation; physical hardware and shipping are separate.
₹12,500 INR in 10 days
0.0
0.0

Hello, I reviewed your PIC16F1829 requirements and oscilloscope video. I have experience with PIC firmware, MPLAB X/XC8, PWM, ADC, and embedded C. Your center-tapped transformer requires two 25 kHz positive PWM pulses on pins 5 and 6, 180° apart, with equal duty cycles (max 45%) and non-overlapping OFF intervals—not complementary half-bridge signals. My approach: 1. Check the schematic, pin mapping, clock, and ECCP/PWM steering feasibility. 2. Implement the two-phase PWM and independent ~190 kHz, 50% output on pin 8. 3. Implement the specified soft start, 95 V feedback regulation, fan control, voltage/temperature monitoring, fault LEDs, and shutdown output. 4. Test timing, duty limits, and fault shutdown; provide MPLAB X/XC8 source, HEX, and documentation. A key point: ECCP half-bridge mode is complementary by default. I will verify a safe alternating-output method before committing to full implementation. Fast hardware overcurrent protection is also recommended. Please confirm: - Can you share the full schematic and any existing code? - What frequency tolerance is acceptable for 190 kHz? - Can you measure PWM and shutdown behavior on the hardware with an oscilloscope? I propose a staged feasibility review followed by firmware development and remote validation. Best regards.
₹10,000 INR in 10 days
0.0
0.0

Hello, I have a technical background in Python, programming, and robotics coursework, and I am interested in embedded systems and firmware development. I have reviewed your PIC16F1829 requirements, including PWM control, soft-start sequencing, voltage sensing, fan control, and fault signaling. I can contribute to documentation, requirements analysis, and test-case planning within my current skill set. For implementation and validation of the power-control firmware, I would want to confirm the existing code, hardware design, and testing requirements before committing to the full scope. I value clear communication, careful validation, and a structured development process.
₹7,000 INR in 5 days
0.0
0.0

Hi, I can develop the PIC16F1829 firmware for your push-pull SMPS controller, including 25 kHz phase-shifted PWM, soft start, closed-loop voltage regulation, fan temperature control, fault monitoring, and LED fault indications. I will also provide the source code and basic testing support. My bid: ₹12,000 (fixed price).
₹12,000 INR in 9 days
0.0
0.0

Hello, I am an Electronics and Embedded Systems Engineer with approximately 8 years of hands-on experience in embedded firmware development, microcontroller programming, and industrial electronic systems. I can help develop and debug the PIC16F1829 firmware for your push-pull power supply application. My approach includes reviewing the hardware configuration and requirements, implementing the necessary control logic, configuring the relevant microcontroller peripherals, and testing the firmware against the agreed operating conditions. I will also focus on reliable startup behavior, fault handling, and appropriate protection logic based on the available hardware and project specifications. I can provide organized firmware source code and implementation notes. My proposed bid is INR 12,000 with a 15-day delivery period, subject to confirming the complete technical requirements. I would be happy to discuss your circuit, expected operating behavior, and existing firmware before starting. Best regards
₹12,000 INR in 15 days
0.0
0.0

Sangli, India
Member since Sep 3, 2026
₹1500-12500 INR
$30-250 USD
₹1500-12500 INR
min $50 USD / hour
$15-25 AUD / hour
₹600-1500 INR
₹600-1500 INR
$5000-10000 CAD
$30-250 USD
$30-250 USD
$15-25 AUD / hour
₹12500-37500 INR
€12-18 EUR / hour
$30-250 CAD
$250-750 USD
₹600-1500 INR
$1500-3000 USD
$250-750 USD
£250-750 GBP
€30-250 EUR
$30-250 USD