Find Jobs
Hire Freelancers

Hardware engineer with some experience in battery management

₹12500-37500 INR

Ditutup
Disiarkan lebih dari 1 tahun yang lalu

₹12500-37500 INR

Dibayar semasa penghantaran
I am looking for a hardware engineer who has got some experience in battery management. The charging curve can be handled mostly in software, but some experience in using ADCs to measure the charge level and logic to limit the current will help. He should be able to design a microcontroller based board for monitoring bettery as well as raw power and switch to battery when raw power is bad.
ID Projek: 34166464

Tentang projek

17 cadangan
Projek jarak jauh
Aktif 2 tahun yang lalu

Ingin menjana wang?

Faedah membida di Freelancer

Tetapkan bajet dan garis masa anda
Dapatkan bayaran untuk kerja anda
Tuliskan cadangan anda
Ianya percuma untuk mendaftar dan membida pekerjaan
17 pekerja bebas membida secara purata ₹34,147 INR untuk pekerjaan ini
Avatar Pengguna
Dear client, I have read your description and I must say I'm intrigued to work with you on this project. I have experience designing static and dynamic battery charging circuits/products. Let's chat and discuss further your requirements. Regards, Yassine
₹25,000 INR dalam 7 hari
4.8 (15 ulasan)
5.7
5.7
Avatar Pengguna
Hello How are you? Thanks for your posting job. I have read your project requirements and I am 100% sure I can complete your project perfectly. ⭐ ⭐ ⭐ ⭐ ⭐ ⭐ ⭐ ⭐ ⭐ ⭐ ⭐ ⭐ ⭐ ⭐ ⭐ ⭐ I have 15 years experience in Circuit & PCB layout design and Microcontroller Firmware design. I will do my best to give you satisfactory results if you hire me. Please discuss about your project in more details. I can deliver your job efficiently within timeline. If you hire me, I think you won't regret. Best regards. Thank you Koba
₹25,000 INR dalam 7 hari
4.3 (23 ulasan)
6.6
6.6
Avatar Pengguna
Good day, I can design microcontroller board for monitoring battery for you in a quality and timely manner. I am an hardware engineer and have good experience in battery management using ADCs. I would like to have a thorough discussion on this project as there are certain suggestions from my side After dedicating more than 30 years to the electronics design and development, I am passionate in designing the best products Technology wise I have worked on all the latest technologies like GSM, 5G, Lora, Microcontroller, ADCs, Monitoring Battery etc. And have worked on more than 20 design tools for designing and simulation purpose Some of the generic queries from my side are: 1. What is the application of this product? 2. What will be the ambient temperature of this product? 3. What are the mechanical constraints to be taken care of? If you are someone who wants to benefit from my experience just message me Hi and I shall be there for you  Regards Hari Mohan Engineering for one is magic for others
₹56,000 INR dalam 2 hari
5.0 (5 ulasan)
5.2
5.2
Avatar Pengguna
Hello, I am an electronics and telecommunication engineer and my major is wireless systems' design. I am experienced in hardware and embedded systems' design. I have designed/printed/tested many PCBs and I am quite experienced with RF design such as designing antennas, matching networks(distributed/lumped elements), filters(distributed/lumped elements), power amplifiers, dividers, feed networks, differential pairs/signals, EMI, clearance areas, shielding for EMI, conducted interference, common mode, etc, LVD, high speed data communication. I also wrote many firmwares and I have checked your requirements I am quite sure that I can help you with your project. Just give me all the details and I will do my best to help you. Best regards
₹25,000 INR dalam 7 hari
4.7 (55 ulasan)
5.7
5.7
Avatar Pengguna
Thanks for posting the project here I am electrical engineer. I have completed many projects in the field of embedded systems and electrical for my foreigner’s client based in USA, UK, Africa, Turkey, Canada, and Germany. I have expertise in embedded and electrical system. Micro Controller • esp32 • Arduino • stm32 • PIC • Mbed • Atmel • AVR • Atmega Microprocessor • Raspberry pi. • MATLAB/SIMULINK • AutoCAD • MPLABXC8 Communication protocols 1. I2C 2. I2S 3. SPI 4. UART 5. Serial Bus 6. CAN bus 7. RS432 Moreover, I can help you in circuit design and PCB designing tasks using eagle, easy EDA, Altium and proteus. I am sure you will consider me for this project when you review my portfolio. I understood the project description I can help you in this task. Your satisfaction will be my first priority, you can trust on me. Contact with me at your earliest to discuss the best cost-effective solution of your task. Best Regards, Muhammad Adeel
₹25,000 INR dalam 7 hari
4.8 (35 ulasan)
5.4
5.4
Avatar Pengguna
Hello. I am a full-stack developer and have much experience for working on Smart IOT device, Embedded and Control System Design and so on. - My Experiences: *PCB Design & Layout - Eagle Cad, KiCard, Altium, PADS, 2-8 Layer PCB *Electronics Design, Circuit Design, Schematic Design *Power Electronics *Wireless Technology *IoT *Micro Controller Hardware & Software *Embedded Systems Design and Solution *Atmel, Arduino, PIC 16F, PIC 18F, STM32Fxx *ESP32, ESP8266 *Raspberry PI *Bluetooth, GSM, WIFI, IR Remote, Transformer Design *Dot Matrix, RGB, LED Dimmer, Temperature & Humidity *Motor (DC, Servo, Stepper, BLDC ) Driver *Solar Battery Storage, ZigBee Communication, RF Technology, DC to DC Converter *Power Supply Design *OLED display, PWM, LCD Display *Prototype Design, Assembling, SMD Technology .
₹37,500 INR dalam 7 hari
5.0 (7 ulasan)
4.9
4.9
Avatar Pengguna
Hello. I am electronic engineer with experience of PCB and programming. ---------------------------------------------------------------- Regards.
₹25,000 INR dalam 7 hari
5.0 (1 ulasan)
1.0
1.0
Avatar Pengguna
Hi I have more than 8 years experienced in circuit design and development in my past I have designed lot Bms system I can design best way without emiemc
₹12,500 INR dalam 2 hari
0.0 (0 ulasan)
0.0
0.0
Avatar Pengguna
Hello, My profile on this site may not reflect my real capabilities and knowledge in the electrical design field because i'm still relatively new here. But i want to ensure you that i'm very well capable and willing to do this project and to kick off my freelance career. I've been working on projects like this for the last 4 years, so surely i can be of help. it's a win win. Thank you.
₹17,000 INR dalam 7 hari
0.0 (0 ulasan)
0.0
0.0
Avatar Pengguna
I and my team work on Electronics Product design and automation at CationCart.com. We have worked on 200+ product design projects for Companies, startups and solopreneurs. I would also like to help you in your project, we have relevant skills of pcb and firmware as you quoted. Regards Katyayan
₹37,000 INR dalam 7 hari
0.0 (0 ulasan)
0.0
0.0
Avatar Pengguna
Hello, I have designed multiple devices that monitor battery. From your brief project description, I concluded that you need a device that can monitor and set charging current, and act as UPS?
₹22,000 INR dalam 7 hari
0.0 (0 ulasan)
0.0
0.0
Avatar Pengguna
Hi, i have working experience on BMS and so pls help to share battery type and load as you mentioned we have to switch row power to battery , however battery is DC source and row power always AC so can you provide more input.
₹25,000 INR dalam 7 hari
5.0 (1 ulasan)
0.0
0.0

Tentang klien

Bendera INDIA
Bangalore, India
5.0
11
Ahli sejak Mac 10, 2016

Pengesahan Klien

Terima kasih! Kami telah menghantar pautan melalui e-mel kepada anda untuk menuntut kredit percuma anda.
Sesuatu telah berlaku semasa menghantar e-mel anda. Sila cuba lagi.
Pengguna Berdaftar Jumlah Pekerjaan Disiarkan
Freelancer ® is a registered Trademark of Freelancer Technology Pty Limited (ACN 142 189 759)
Copyright © 2024 Freelancer Technology Pty Limited (ACN 142 189 759)
Memuatkan pratonton
Kebenaran diberikan untuk Geolocation.
Sesi log masuk anda telah luput dan telah dilog keluar. Sila log masuk sekali lagi.