Sedang Disiapkan

Create RF receiver and transmitter

I require the Complete PCB design and Firmware for the following:

RF Transmitter:

434,000 MHz

PCB to fit pre-designed enclosure

Battery Operated

3V CR2032 Preferred

Transmitter power >10dBm

Minimum Standby Current draw <10nA

PCB solder bridge to select Channel 1 or 2

Channel Selection done via a soldering bridge. Eg. Channel 1 J1, Channel 2 J2

Each Transmitter should be unique as to not interfere with other receivers in near proximity.

Specific button to be used. datasheet will be supplied

Enclosure DXF and Step file will be supplied to fit PCB into enclosure.

Cost effective PCB design is required.

RF Receiver:

434,000 MHz

2 Channel Wireless Receiver

9 – 32VDC Operating Voltage

Positive Output (Latched until Negative unlatch received)

Unlatch Negative input

Negative Output Channel 1 (Momentary) 2A

Negative Output Channel 2 (Momentary) 2A

Built in Buzzer (Buzzer signal when RF signal received, NO SIGNAL if LATCH ON)

Buzzer Specs: PCB Mount; 3500Hz; >90dB;

Learn Button ( PCB mount button )

Pair up to 50 individual transmitters

RGB Status LED

Should be resistant against irradiated and induced electro-magnetic noise

Learn Mode should reduced range to 50cm.

Transmitter Low Battery LED.

Low Battery LED should illuminated if last received transmitter battery is low.

All inputs and outputs should include short circuit protection, over current protection, reverse polarity protection.

Connector specifications will be supplied.

PCB Size limitations: Width 55mm, 45mm usable. Length <80mm

System should have a range of 50m

SMD components preferred for production.

Products should be economic to manufacture.

Products should comply to EN 300-220.

This project should include all PCB Gerber files, Altium files, Firmware for devices and source code as well as the code project for the Transmitter and Receiver.

Kemahiran: Susun Atur PCB, Elektronik, Kejuruteraan Elektrik, Rekabentuk Produk, Mikropengawal

Lihat lagi: create satelite receiver, receiver transmitter wireless schematic diagram, bluetooth voice receiver transmitter project, homemade transmitter and receiver, rf transmitter and receiver pdf, rf transmitter and receiver circuit diagram pdf, rf transmitter and receiver arduino, rf transmitter and receiver block diagram, rf transmitter and receiver kit, how to make a radio transmitter and receiver at home pdf, how to make a transmitter and receiver for rc, create pop3 receiver, simple receiver transmitter, require send button lync, card receiver transmitter, create smpp receiver java, design bluetooth receiver transmitter, motor receiver transmitter circuit, create a poster that i can use on facebook and other, design a logo i require

Tentang Majikan:
( 0 ulasan ) Uppington, South Africa

ID Projek: #22341900

Dianugerahkan kepada:

liveexperts123

Hi there, I have read your project description and i'm confident i can do this project for you perfectly.I still have a few questions. please leave a message on my chat so we can discuss the budget and deadline of the Lagi

$250 USD dalam 20 hari
(80 Ulasan)
7.4

17 pekerja bebas membida secara purata $700 untuk pekerjaan ini

chandra2sekhar

Hello,Myself [login to view URL] Sekhar,[login to view URL],Phd from Cdeec Innovations,[login to view URL] have 15+ years experience in Electronics Product development. we have in house pcb fabrication facility for protoypes.i have worked on many IO Lagi

$750 USD dalam 7 hari
(45 Ulasan)
7.7
MIKY4227

Hi ser good day i have more device with equivalent caracteristic please see my portfolio for test my work used more of 434 MHz lora with maximun long are 5000 mt at free .send full proyact in Altium send SCH PCB gerbe Lagi

$1500 USD dalam 30 hari
(52 Ulasan)
6.4
dalong243020

Hello. As an electronic engineer, I have been working in PCB design/layout and firmware programming field for 18+ years. Here are some of the experiences that I worked ago. - Schematic and PCB Layout Lagi

$500 USD dalam 7 hari
(8 Ulasan)
5.9
CoherentTech123

Dear Sir, I am an expert with more than 15 years of experience in firmware development, prototyping and PCB Layouts. I have worked on 8-bit, 16-bit and 32-bit MCUs developing ultra-low power designs and compl Lagi

$750 USD dalam 30 hari
(47 Ulasan)
6.0
smartman7102

Dear client, Nice to meet you. I have been working as a firmware and hardware designer for many years. I had developed several similar projects using the various microcontrollers such as STM32F1/2/3/4/7xx, PIC16/18xx, Lagi

$250 USD dalam 7 hari
(12 Ulasan)
4.4
smarthardware

Hi, I read your project description. Your project is really interesting to me and i have many experience working with PCB design, manufacturing functional prototyping with firmware programming, adroid app, and test. I' Lagi

$500 USD dalam 7 hari
(2 Ulasan)
3.8
yousufhusain434

Hi I'm an electronics engineer & pcb designer with 5 years experience. I can help you in this project. Please Send me a Private message so that we can discuss more about it. Thank you.

$500 USD dalam 7 hari
(3 Ulasan)
3.5
schoudhary1553

Hello, I have gone through your job posting and become very much interested to work with you. I am an expert in this field. I have already completed several projects like this. For evidence you can see my profile. Pl Lagi

$500 USD dalam 7 hari
(2 Ulasan)
3.4
bandrey

Hello, I can help you and I have a question. If you want to use CR2032 for 10 dBm. What should be the lifetime of the transmitter?

$2000 USD dalam 30 hari
(2 Ulasan)
3.1
articreations

Hello, I'm Aarti- freelancers .. Graphic designer with experience of 7 years. There have long been working on many projects for more years. I'm glad I can help you in your design work and do a good job,if you Lagi

$251 USD dalam sehari
(3 Ulasan)
2.2
prodeve

Hello, Thank you for sharing the requirement of your project. We read your requirement and we understand it. To understand more and clarify our doubts, we want to talk with you. Therefore, send us a message so that Lagi

$700 USD dalam 8 hari
(1 Ulasan)
2.0
javiernicola

Hello, first of all congratulation for the very complete articulation of your requirements. Im a telcom electronics engineer working in the aerospace industry (IT), i have a ton of experience with arduino and PCB desig Lagi

$800 USD dalam 9 hari
(1 Ulasan)
1.4
AlinaKornilova

<-----Dear,sir. you will not waste your gold time.------> Dspic30f6010A, pic16f877A Altium. Proteus. MPLAB. I’ve carefully gone through your job post. I am very much interested in your project with all of your requ Lagi

$500 USD dalam 7 hari
(0 Ulasan)
0.0
sirajahmadzai

Dear Hiring Manager, After reviewing your job description, it’s clear that you’re looking for a candidate that is extremely familiar with the responsibilities associated with the role, and can perform them confidentl Lagi

$750 USD dalam 7 hari
(0 Ulasan)
0.0
dainikpatel

Greetings, We are an India based company. We deal with embedded hardware and firmware development. Our company offers services all over the globe. Recently, we have developed a product with BLE technology. Our enginee Lagi

$950 USD dalam 40 hari
(0 Ulasan)
0.0
chiboub

Hello, thank you for your job posting. I am a senior device developer. I have plenty of experience in firmware development and micro-controller developments. I can write the firmware based on Arduino, Raspberry Pi, Pic Lagi

$450 USD dalam 7 hari
(0 Ulasan)
0.0