Ditutup

3 PCB Designs for Prototype Production / fairly rudimentary and well documented

I am looking for a PCB designer who can turn my 3 sketches into technical drawings so that I can have these 3 prototypes produced. (The one who does this job (well) will get approx. 1-2 other jobs after this is done)

PCB #1 power distribution -converter -ups -analogue_timed_switch

PCB #2 analogue data distributor

PCB #3 data and power distributor

For each board there is a separate sketch of the layout and connectors, I provide this as .eps .pdf and as printable A3/[login to view URL]; for better understanding, each board comes with an illustrated [login to view URL]

To the functions of the individual boards:

PCB #1 power distribution -converter -ups -switch

- In front of this board is a fuse (therefore not included);

- The 240V current will be directly led to a plug and a terminal

- The 240V power must then be converted to 12V to charge a battery (12V approx. 10Ah [fuse required?]) which will act as the ultimate power supply (UPS) for the rest of the circuit.

- After the UPS one line of the 12V power is connected to a plug (approx. 3A/36W)

- Additional 3 individual slots for PC fans (approx. 0.3A/3.6W each, 3 Pin Molex 22-23-2031]) are powered (tachometer signal is irrelevant)

- The 12V current must be converted to 5V afterwards

- One line of the 5V current is led to a plug (approx. 10.8A/54W)

- A further line is routed to an "analogue timed switch" (below), from which 2 plugs (A/B) must be operated (approx. 5V/3A each)

# Analogue timed switch

1 - Gets a plug for a button

2 - This 'self-developed' switch should only power one of the two connectors (A/B) at a time

3 - As soon as the button (1) is pressed, the switch should give a signal to the active port ([A]/B), wait 120 seconds, then cut the power supply from the current port and feed the other port (A/[B]). And vice-versa. It doesn't has to remember the last active port (only if that's no hassle to realize)

= Only one RaspberryPi at a time will be powered by GPIO from the A/B ports, they must never run simultaneously.

PCB #2 analogue data distributor

Two RaspberryPi4 are connected to this board, but only one is running at a time; both must have access to the same peripherals.

PCB #3 data and power distributor

Distributes power and data from different connections.

Technical details such as the safety of the conductor paths for different voltages and the individual components to be used to realize the requirements are the task of the freelancer.

I rely on a proper implementation of the UPS and the analogue timed switch.

The circuits (especially PCB#1) have to be protect against over/under-voltage, over-temperature and against short-circuit. Appropriate PIN Connectors/Terminal blocks should be chooseand have 'securing-clips' so they won't come loose.

The boards do not necessarily have to be tiny, but one should consider production costs.

The connections should be at the positions as shown on the sketches, but this is only for orientation they don't refelct any dimensions (except PCB#3 bottom and right side). The labels should obiously be printed on the PCB.

As said I'd have 1-2 follow-up jobs, additionally to the production of the cables.

Happy to hear from you and to negotiate

Best regards,

Max

Kemahiran: Susun Atur PCB, Elektronik, Kejuruteraan Elektrik, Rekabentuk Produk, CAD/CAM

Lihat lagi: production company business card designs, production logo designs, typical price pcb design prototype, alpha prototype, what are the three components of the testing and prototyping?, prototype development services, prototyping in product design, prototype production meaning, stages of prototyping, prototype development process, gamma prototype, visiting card designs samples music production companies, circuit designs regulated power supply pcb, engineering projects pcb designs, outsourcing jobs pcb designs, PCB designs, post production environment modelling 3ds max tutorials, embedded ethernet pcb designs, bridge type pcb designs, bus master converter pcb board prototype

Tentang Majikan:
( 0 ulasan ) Bolzano, Italy

ID Projek: #27513668

20 pekerja bebas membida secara purata $323 untuk pekerjaan ini

(57 Ulasan)
7.0
binyameen441

Hello, thank you for your job posting. I read your description about--PCB I am a senior electrical engineer. I have plenty of experience in firmware development and micro-controller developments. I can write the firmwa Lagi

$50 USD dalam sehari
(102 Ulasan)
6.3
(36 Ulasan)
6.2
Mestek

hello I am a computer engineer,I have masters in computer engineering,I have experience for more than 8 years in arduino and electronics i can make to u the required design for your 3 PCBs and deliver to u all the nece Lagi

$444 USD dalam 7 hari
(31 Ulasan)
5.5
Sukanta0110

✋ Hi! I am completely familiar & experienced to the project. I can complete your project with perfection . I have completed my [login to view URL] in Electrical & Electronic Engineering. I have been working on the field of Microcon Lagi

$50 USD dalam sehari
(37 Ulasan)
5.0
Andrii0125

Hi. I am an electronic engineer with rich experience over 10 years. I have read your project description very carefully, I am interesting in this project. I will finish your project in time perfectly. Best regards, And Lagi

$500 USD dalam 7 hari
(14 Ulasan)
5.1
HarimohanG

Dear Max, I am PCB Designer and could these 3 prototypes produced. I have read and understood your requirements and could do it for you in the least time and utmost superior quality. I have experience in PCB Designs fo Lagi

$450 USD dalam 2 hari
(2 Ulasan)
4.4
SMBelectronics

Hello Max I hope you doing good I read the complete details of the project and I am interested in working on them, I am an electronic engineer from India with 3+ years of experience in Circuit and PCB Layout designs, I Lagi

$750 USD dalam 7 hari
(16 Ulasan)
4.8
pcbdesign88vn

Dear you, I have 8 year to design circuit in Altium. We can discuss more on chatting. I will give you the best result. Brg!

$50 USD dalam 7 hari
(16 Ulasan)
4.2
aliabidlodhi74

Hello... I have read your requirement you want PCB board development. Lets discus details in chat I have master degree in Mechatronics Electronics Engineering and I have 7 years of Industrial experience in dealing wit Lagi

$50 USD dalam sehari
(6 Ulasan)
3.4
bwtxzj

Hi I am a professional PCB designer and can complete your project. I will supply all type of files including gerber file. Please contact me.

$400 USD dalam 7 hari
(2 Ulasan)
2.6
macroenergy

I have read your description and understand everything. I will design your board by using Altium. I will place component at necessary place in board. Since I have large library which is done by XBL files, it is no mist Lagi

$250 USD dalam 7 hari
(4 Ulasan)
2.9
sondagarharesh

Hello sir. Hope you doing well. I read your requirement very care fully and I think we can do it with our best As you discuss about pcb layouts All the things will be easily done by us First of all. We are a high Lagi

$450 USD dalam 7 hari
(4 Ulasan)
2.7
lanceruvc

Hello We have experience in this field Previously for more details please contact us. We are the team of expert with great experience in there field as listed below 1. Industrial Automation 2. PCB Designing & Ma Lagi

$450 USD dalam 7 hari
(2 Ulasan)
1.8
boitalicroy7

Hey there, I hope you are doing good. I am ELECTRICAL/ELECTRONICS ENGINEER from India with 4+ years of experience in designing PCBs. I am familiar with various CAD tools including tools preferred by Manufacturers. I a Lagi

$200 USD dalam 4 hari
(3 Ulasan)
1.5
Mrshann

I have just read your job description and I can design double side and multilayer PCB layout in a minimum size you want. I assure you will provide quality work that will meet your expectations. I have many experiences Lagi

$350 USD dalam 5 hari
(2 Ulasan)
1.6
GERGX

Hello I have 8+ years of experience in PCB design and layout, firmware programming, and rapid prototyping. I have support -PCB layout and schematic capture with Altium, Cadence, Eagle, etc., with multilayer, flexible, Lagi

$250 USD dalam 7 hari
(1 Ulasan)
1.7
TechXInnovation

Hi there, Max. Hope you're doing well. I have gone through the attached files and I am delighted to inform you that we will be able to complete all your PCB designs. We are efficient and our hefty experience in this fi Lagi

$250 USD dalam 7 hari
(0 Ulasan)
0.0
vikramec08

hi, I have experience of 10 year in power nd embedded field nd help you in making design ,we use ki cad for pcb development so may not bee a issue nd send you all require details . the power stage will be low of nd if Lagi

$444 USD dalam 20 hari
(1 Ulasan)
0.0
chiranjeevi12393

Good experince on ATE board pcb design and commercial layout [login to view URL] contains microprocessor, crystal, power circuit etc.

$167 USD dalam 7 hari
(0 Ulasan)
0.0