Sedang Disiapkan

RFID module design and Prototype

Create a 3D model of an RFID module holder, detailed drawing to be provided. The device is approximately 3 inches wide, ¾ inch tall and 2 5/16 inches deep. The project bid should include design, sourcing and production of a total of ten prototypes for testing, deliverables are listed below:

1. Review of design and recommendations for production options.

2. 3D design based on drawings provided.

3. Conversion of measurements to metric, if necessary.

4. Source file for 3D printing and recommendations for file format.

5. Prototypes to be produced in black using ABS or some other equivalent flexible, durable material.

6. Time line for completion of project.

Milestones will be agreed to by both parties before project is started.

Following is the revised project, I have simplified the design and modified the dimensions slightly, I have also provided a revised drawing:

Create a 3D model of an RFID face plate, detailed drawing is attached. The face plate is 3 1/4 inches wide, 1 inch tall and 5/16th inch thick. The project bid should include design, sourcing and production of a total of ten prototypes for testing, deliverables are listed below:

1. Review of design and recommendations for production options.
2. 3D design based on drawings provided.
3. Source file for 3D printing and recommendations for file format.
4. Prototypes to be produced in black using ABS or some other equivalent flexible, durable material.
5. Time line for completion of project.

Milestones will be agreed to by both parties before project is started.

Kemahiran: Reka Bentuk 3D, Penerapan 3D, jQuery / Prototaip

Lihat lebih lanjut: the metric line, prototype review, prototype 3 review, printing and design, on line 3d drawing, on line 3d design, jquery include, include jquery, drawing for 3d printing, create a prototype, create 3d model for printing, 505 design, 3d rendering or drawing, 3d printing rendering, 3d printing design, 3D module, 3d model source, 3d model material, 3d model for printing 3d, 3d model for drawings, 3d model for drawing, 3d model for 3d printing, 3d model and printing, 3d design rendering, device testing

Tentang Majikan:
( 1 ulasan ) Roseville, United States

ID Projek: #4075792

Dianugerahkan kepada:

MEINVEXCELLENT

Hi, Dear. Thanks to share this project to me.

$30 USD dalam sehari
(0 Ulasan)
0.0

7 pekerja bebas membida secara purata $1247 untuk pekerjaan ini

bradleysnider

YOU BUDGET IS $100? I saw the design PDF this is a lot of work for $100?!

$7000 USD dalam 99 hari
(3 Ulasan)
4.0
mhom2x

Hi, please check pm. Thanks.

$30 USD dalam sehari
(1 Ulasan)
1.4
eried

"The project bid should include design, sourcing and production of a total of ten prototypes for testing, deliverables are listed below:" Also shipment? I can design them and print them but probably is faster if you Lagi

$400 USD dalam 60 hari
(0 Ulasan)
0.0
modeomedia

Hi, You can visit my website at The Administrator removed this message for containing contact details which breaches our Terms of Service I look forward to hearing from you. Warm Regards, Dennis

$100 USD dalam 3 hari
(0 Ulasan)
0.0
Xuyao

Dear Sir, I'm profesional mechanical design engineer specializing consumer electronics enclosure design. I'm running 3d design to prototype at daily base. Thanks!

$100 USD dalam 7 hari
(0 Ulasan)
0.0
Maodesign

Hello. Please check my portfolio. I'm an expert industrial designer in RFID module project. [url removed, login to view] This is a pdf file regarding my graduated thesys w Lagi

$100 USD dalam 7 hari
(0 Ulasan)
0.0
Bradxenon

I am a Civil Engineer with applicable 3D modeling knowledge and EI certification to assist you with your project. Your budget is set too low for your requirements. Also, it is not clear if you would like the prototypes Lagi

$1000 USD dalam 7 hari
(0 Ulasan)
0.0