Automated blinds using arduino and light sensor. Prototype only small scale.

Hello i have experience in designing electronics circuits and can program microcontrollers. I will make your project practically on breadboard and will provide you circuit, code and PCB design. Thanks Relevant Skills and Experience Arduino Electronics PCB Layout Proposed Milestones ₱25000 PHP - Deliver the project.

Hi I hope you are doing well. I have experience in automatic blind control system. I have understood your project requirements and I would like to discuss it in more details. Looking Forward Khawaja

I have a lot of experience developing and prototyping different devices based on arduino and other MCUs, please contact mew with more details of your project. Stay tuned, I'm still working on this proposal.

Hello I'm an electronics engineer with 10+ years of experience and can do the job. Please tell me more about your project. Best regards, Dennis Relevant Skills and Experience Arduino, Electronics, IoT Proposed Milestones ₱11111 PHP - Job done

Hello, I believe I could help you with this project as I have all relevant experience in this field. Relevant Skills and Experience More than 15 years of professional hardware design with microcontrollers and firmware development. Proposed Milestones ₱4000 PHP - Hardware schematics design ₱6000 PHP - PCB design ₱10000 PHP - Firmware design ₱7777 PHP - Compiling all documentation

I am an Electrical Telecom Engineer with more than a year experience in Embedded industry. I have also worked as a freelancer for more than four years now. I have plenty of experience with arduino. Relevant Skills and Experience I have written codes for sensors like ADXL335 and 345, Xgbee,UART, I2C, SPI protocols, Radar, magnetic sensor, LCD, keyboard and lots of other sensors and produced industrial grade equipment. Proposed Milestones ₱22222 PHP - automate blinds project

i have a good knowledge about microcontroller programming and have done number of projects using microcontroller i also have good knowledge about hardware for interfacing with microcontroller. Relevant Skills and Experience 4 year of experience in embedded system working on different microcontroller 8051,PIC,AVR,ARM,Arduino Proposed Milestones ₱22222 PHP - 22222

i have big expirience with electronic, arduino, developing schematic and pcb design. I worked on projects like a smart home systems. i work in Altium designer (routing 2,4,7 a layer board). i am assistant profesor on faculty(department electronics). best regards

I am a hobbyist working mostly on arduino and AVR micro-controllers. I am capable of designing single layer through-hole PCB using KiCAD. I have a certified training in PCB Design, Advanced Embedded System Design and Wireless sensor Networks. SInce your project is a simple prototype, it can be completed with the lowest budget using only one arduino, a stepper motor and a light sensor along with a few passive components. In the first step, I will design a circuit schematic and a single layer PCB design for the project. This step will be followed by software/code design and a rough sketch in arduino will be written. In the final step, hardware is assembled as per the requirement and the design will be tweaked for final adjustments. Shipping charges are extra (I live in India). Please contact for any further info.

I am Electronics Engineer and expert in Arduino and IDE. Please Contact Relevant Skills and Experience Arduino, IDE, Programming Proposed Milestones ₱10000 PHP - initial ₱10000 PHP - final Give me all the details

A proposal has not yet been provided

A proposal has not yet been provided

I do electronic circuits with lighting, leds and motors using raspberry pi and arduino. For the blinds you just need a photocell and the arduino programmed to make the motor close/open the blinds. Relevant Skills and Experience Working with LED strips, motors interface circuits and software development Proposed Milestones ₱19999 PHP - Completion Can you provide more details about this? What type of blinds are to be used? Vertical, horizontal?

Hi there I will give you all the codes commenteds so you can understand or even develop further the codes, schematics and obviusly all the explanation of the project Habilidades y experiencia relevante Arduino and Atmel MCUS for more than 5 years, actually lead programmer and head of the R&D department at a small lifter company in venezuela Htos propuestos ₱22222 PHP - full delivery

This project is familiar to me as my colleagues have done same project at my college Relevant Skills and Experience I have helped my friends in this project Proposed Milestones ₱22222 PHP - aaa

I will complete this work on time, As I've good skills on Arduino. Relevant Skills and Experience Have Arduino certification. Proposed Milestones ₱22222 PHP - will complete your project on time. You need coding or Something else?

I believe the offer can be improved, based on your requirements and final specifications. Habilidades y experiencia relevante I work with arduino, mostly daily, have experience with variety of sensors, and my current PCB designs are currently installed on some places like "El Globo" a mexican bakery, mainly fpr domotics app. Htos propuestos ₱22222 PHP - Total project ₱5000 PHP - Schematic design ₱5000 PHP - Simulation file ₱5000 PHP - PCB design ₱5222 PHP - Gerber files for production ¿Can you explain me the complete project? Also with small details

isaw your project and i have required skills to accomplish it Relevant Skills and Experience i am electrical and electronics engineering i had worked in similar projects before i have experiences with pcb design , arduino shield design ,arduino programming and i can design using proteus Proposed Milestones ₱27777 PHP - pcb design

I worked in several projects using arduino in making a gps tracker for bags and rc car and self driving car

A proposal has not yet been provided