Kejuruteraan Elektrik Jobs

I am Looking for an engineer that can update the Schematic and PCB of an audio board. Need to Update/add connectors such as MIDI connectors, audio connectors, USB, memory, board size, etc The PCB is in CADstar format, The Schematic is in Orcad format. I have schematics and PCB files, I you have CADstar is a Plus. Our Organization shall keep the rights to the work. NDA and Contract is required.

I want to make high voltage dc power supply, regulated high voltage upto 100 kv and 2 mA current . I require the list of parts required, with suppliers location ( preferably ) in Maharashtra or Hyderabad or Online with price details of the parts and ASSEMBLY drawing and process.

Addressing over power using modulation NDA will be required for this project but this is a small project for someone with skills as mention.

We require someone to read the energy reports attached and outline why there is such a high amount of energy usage on certain days and within certain hours of the report. First analysis will need to be provided t be awarded the job so we can confirm you know what you are talking about and then a full comprehensive report will be required to be created upon awarding the job.

I am sole proprietor Architect, and have a small 2,700 s.f. addition to a church. I have Lighting and Power floor plans finished and just need Electrical Engineer to correct and/or fill out a panel schedule that I started. I am uncomfortable with what I have done and need a licensed Electrical Engineer to review this for me.

I need to run a three phase unbalanced distribution load flow MATLAB code for IEEE 13 bus. After that using WLS I need to do the State estimation for Voltage, angles and Powers. Anybody interested and highly experienced in this field will be given the work and payment will be high too. Once you show your interest I will share all the required data, algorithm and documents needed to do the MATLAB c...

I am looking for a tutor to teach me

I need a single line diagram for a 33kw solar electric system. Its a 3 phase 120v/208v , system using (91) 370 watt panels and 3 Fronius 3 phase inverters. It will connect to a 800A service.

I need a circuitboard design for LED lights being triggered by a motion sensor and a photo receptor.

WSNs in matlab and some other details

I have designed a IOT based board using ESP. I need an expert ESP developer.

El objetivo general del presente proyecto consiste en la realización, verificación funcional y validación experimental de un microcontrolador sencillo basado en un subconjunto de la arquitectura del juego de instrucciones del RISC-V. El microcontrolador debe ser descrito en SystemVerilog de modo que sea sintetizable y pueda ser implementado en una FPGA Cyclone IV de Altera. Su...

i want only 4 new method of image fusion based on previous methods of image fudion

I need some help with my business. I start dairy farm project

I need someone who can help me know the difference between Watts, Volt because i have a solar generator and i need someone for help

Design and develop vending machine communication and control platform using Arduino, 21rpm high torque vending machine 12v dc gear motor (40 motors), REES52 IR Infrared Sensor Module, wifi Module. Also need continuous support during the testing of the functionality on the actual vending machine.

Hey I want an expert who can do this project really quick. Within 10 hours. Budget is aud 25 fixed. Bid only if you're interested. Message me for details

I need someone who can make neural network to [log masuk untuk melihat URL] more details

Looking forward for Freelance Field Service Engineer for Scientific equipment (Water Filtration system) and Safety Cabinet. Preferable local Indonesia which has good technical skills and own transportation.

Pic micro controller to measure 3 phase voltage and current measurement & control the relays based on current readings

need a Matlab code(not simulation) to simulate grid connected micro-grid,with PV, wind, load and battery.

lane keeping control using matlab image processing toolbox with simple PID, PI or PD controller in aduino and adafruit motor shield. Just as in the video I want to be able to control using arduino. please check this link for better understanding [log masuk untuk melihat URL]

Need to log keypad strokes from a 4x4 keypad with arduino

Design a bias network using Cadence Spectre (or other CAD software as longs as I can easily follow your steps). Must generate a 10uA current with gm = 100uS that cannot vary by more than +-10% over -40 C to 130 C or supply variations of +-10% with a nominal 1.8V supply. You come up with the idea of using a constant gm bias circuit to bias the amplifier. Design the bias network and determine the d...

Field Oriented Control For BLDC motor

I need a fully functional hardware software prototype for an iOS audio receiver project. I have C Code available for Linux that needs work. Features: QCA7500 (ARM1156) based board iOS audio receiver Add i2c transceiver i2c auth chip Add i2s transceiver to get ALSA i2s output Discrete 44.1 kHz CPU OCXO clock, 0.5 ppm tied to i2s transceiver QCA7500 Homeplug powerline network driver No Ethernet / W...

We want to send existing code instructions from Raspberry to two arduino mega. The instructions must be able to be sent from Raspberry to each arduino simultaneously. The the arduinos send the signals to the controllers which move the stepper motors. Each arduino is connected to eight stepper motors and they must be able to move simultaneously.

Need a prototype for a project. My needs are: Hardware * An Arduino based PCB * Two temperature sensors, preferably DS18B20 - The first temp sensor attached to a 1,1 meter long cable -The second temp sensor attached to a 0,2 meter long cable * A GSM shield, preferably SIM900 or other GSM shield that will work world wide * Re-chargable battery, preferably standard size AA * A battery holder * on/o...

We want to make some modifications to a phone circuit so that when the headphones are plugged in the front microphone will still work rather than be disabled Thanks

We want to find a solution to keep the front mic enabled whiles the phone is in headset mode on a feature phone Nokia 105

Mainscope: Engineering, PCB Layout Design, Embedded Software, prototype - Induction heater Power : 2KW Frequency : 8-30kHz Input Voltage : 350VAC 60Hz Single Edge quasi resonant Dimension : 25 mm x 25 mm x xmm (the depth is independent) Controls: -Current measurement -Voltage measurement -4 digital Inputs -4 digital Outputs -Can Bus The power parts and MCU has to be...

I want to build a product with very similar specifications to this one: [log masuk untuk melihat URL] The job is to design a schematic for a product which would meet the following requirements: Read animal RFID Ear tags(134.2Khz) at a range of 1 meter or more.(This is the difficult part) It will be made of two parts.1 - RFID Reader, 2 - Antenna Enclosure design is not required at this stage. S...

comprehensive understanding of theory and mathematics of stenography or information hiding in general. learn how to program with matlab and how to implement project specific functions/algorithms for multi media stenography. the application of stenography for digital multi media content. explore teh application of these algorithms. create GUI in matlab. final report 8000 words.

I want you to design a chipset for wireless Active Noice Cancellation Headphones. If you have any query, we can discuss over chat. Feel free to message me.

Hi, I am looking to have both the upper and lower PCB reverse engineered. Schematics and PCB layout drawn up. Thanks

long range wireless rfid reader

Hello, I'm looking for someone who can help me in building a drone. I have the basic schematic set but need some finetuning.

I Want to make a Smart UPS Circuit simulation + PCB hardware which can pass EMC test • you have to give me full details other circuits why not recommended and why your circuit recommended. • Must show digital current and voltage usage and total voltage and total current • Can be modified by battery size • Explanation Supporting Material Comparison of Results with Other Model...

Hi, I need a Freelance Electronic Engineer to solve this issue:[log masuk untuk melihat URL] llook mainly at the [log masuk untuk melihat URL] and [log masuk untuk melihat URL] (phone access and delete and to this (videos) [log masuk untuk melihat URL]

I am a freelance footage & timelapse content producer. I want to build a timelapse slider, with the ability to trigger camera (intervalometer function) using arduino. I currently have dowloaded 2 different sketch: 1. an advanced camera intervalometer/timer 2. shoot-move-shoot slider stepper motor controller. I would like to combine these two sketches into a single program. The hardware tha...

We are Hiring Good Programmer in FPGA, GPU, CUDA, MATLAB for our Company. (Removed by Freelancer.com Admin)

analysis for solar thermal power plant using EES SOFTWARE + SAM EES will be used to do analysis for thermal part SAM will be used to do analysis for thermal part and solar part .

hi, freelancers! file of PCB board. -max duration : 8~12s, So that the viewer cannot see every detail. -Animation

Fabrication of general purpose "Potentiostat/ Electrochemical analyzer" capable of doing analysis most widely used techniques such as Cyclic Voltammetry (CV) and Linear Sweep Voltammetry (LSV), Normal and Differential Pulse Voltammetry, Square Wave Voltammetry, Chronoamperometry Specifications: Potentiostat : CV and LSV scan rate: 0.00001 to 1000 V/s or better Max Current: ± ...

I need a small touchpad (2cm X 2cm max.) for using on PC. (USB or wireless) We may use a custom printed circuit board (PCB) design and layout or even use a Blackberry trackpad for this purpose. [log masuk untuk melihat URL]:[log masuk untuk melihat URL] [log masuk untuk melihat URL]

I want someone who can code using uVM and build a layered testbench for an LC3 Micro Controller.

Development of energy-efficient multipath routing protocols for wireless sensor network with static sink node

2.5 kw aircon install at Belmont NSW 2280.

3D builder is a software that allows you to create objects and print them seamlessly. I need the 3d printer too connect to a lcd screen which has a processor that can run the 3d builder software 3d builder has a print option and when it is clicked i wish the 3d printer to automatically print the object, the user will create seamlessly I also need the 3d printer to enable a mouse so the user can n...

The project is described in the uploaded file, however one can alter the project as long as keeping the equipments and the goal of the project intact