Find Jobs
Hire Freelancers

Product Development

£20-250 GBP

Ditutup
Disiarkan lebih dari 7 tahun yang lalu

£20-250 GBP

Dibayar semasa penghantaran
Hey guys i have attached all relevant files below please take a look at them all before starting because they will help you very much with the assignment Here is the assignment sheet Verification Analysis Part 1 Using the reference file [login to view URL] and Mentor Graphics Hyperlynx, focussing on just the SPI associated nets between U1 and U2. a. Run a batch analysis and identify any problems for crosstalk or impedance. (comment on results, screen shot alone is insufficient) [10 marks]. b. Produce a waveform simulation for the net S17_SPI_CLK, with clock speeds of 25 MHz and 50MHz, with R65 set to 330Ω. What is the delay between transmission at U1 and receipt at U2? Describe the waveforms at the transmitter and receiver, identifying what is happening. Change R65 to 33Ω and re-simulate. [10 marks] c. Export the net to LineSim, adjust the nets parameters (by adjusting resistor values and track widths only) to improve the SI and produce a new waveform simulation and value for the delay with clock speeds of 25 MHz and 50MHz. Describe what the problem(s) with the nets trace parameters were, and how they were corrected. [20 marks] 2. Verification Analysis Part 2 For development the microcontroller (U2) is linked via J6 to the external world. Part of which is the Serial Wire Debug lines of SWCLK and SWDIO. Simulate communications at 25 MHz using the IBIS generic_model 74ALSXX Line driver (3V3 level) for the J6 pins (as outputs). Open the reference linesim file [login to view URL] in Mentor Graphics Hyperlynx, which is an export of the SWDIO transmission line from part 1; simulate the following termination methods, choosing appropriate component values (give reasons why these were chosen), include screen shots of the simulated waveforms (horizontal scale set to 10ns/div), and line schematic: (describe waveforms and any problems) a. No termination b. AC termination c. Thevenin (Pull up to VCC_MCC_3.3V) d. Shunt resistor e. Series Resistor [10 marks/section] Recommend which of these is the most suitable for this particular application and justify your answer. Tanks for reading
ID Projek: 12894163

Tentang projek

5 cadangan
Projek jarak jauh
Aktif 7 tahun yang lalu

Ingin menjana wang?

Faedah membida di Freelancer

Tetapkan bajet dan garis masa anda
Dapatkan bayaran untuk kerja anda
Tuliskan cadangan anda
Ianya percuma untuk mendaftar dan membida pekerjaan
5 pekerja bebas membida secara purata £223 GBP untuk pekerjaan ini
Avatar Pengguna
Hi Sir I am an expert PCB designer with more than 8 years of experience I can do the required testing of the product Please get in touch to discuss it further I am waiting for your reply to start Regards
£500 GBP dalam 7 hari
4.8 (154 ulasan)
7.2
7.2
Avatar Pengguna
kldsfjalkgjklajfdlkajgkaglkajglkajgklajglkamgvklasjdflkahglkajgjkaglkjagkljalkgjlkajglkajglkagiwejrlkjr
£333 GBP dalam 3 hari
4.4 (4 ulasan)
3.1
3.1
Avatar Pengguna
Hi sir I gone through your requirements of the project I have know the pads hyperlynx signal integrity If you need more information about me please see my profile Thank you
£111 GBP dalam 3 hari
4.2 (1 ulasan)
0.6
0.6
Avatar Pengguna
I have a Master's in Electrical Engineering and I have worked on termination, pcb design, circuit design.
£23 GBP dalam 3 hari
0.0 (0 ulasan)
0.0
0.0

Tentang klien

Bendera UNITED KINGDOM
United Kingdom
0.0
0
Ahli sejak Jan 25, 2017

Pengesahan Klien

Terima kasih! Kami telah menghantar pautan melalui e-mel kepada anda untuk menuntut kredit percuma anda.
Sesuatu telah berlaku semasa menghantar e-mel anda. Sila cuba lagi.
Pengguna Berdaftar Jumlah Pekerjaan Disiarkan
Freelancer ® is a registered Trademark of Freelancer Technology Pty Limited (ACN 142 189 759)
Copyright © 2024 Freelancer Technology Pty Limited (ACN 142 189 759)
Memuatkan pratonton
Kebenaran diberikan untuk Geolocation.
Sesi log masuk anda telah luput dan telah dilog keluar. Sila log masuk sekali lagi.